249

Reproduction Generator for the Model 249 Lantern. Generator includes gas tip, springs, and tip cleaning wire. Made in the USA.

Reproduction tip cleaning needle for the 249 kerosene generator.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

This is an used original old red letter logo globe used on lanterns from 1960 to 1980. Although used it will be in good condition. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

This is a brand new clear globe that will fit models 200, 200A, 200B, 201, 202, 242A, 242B, 242C, 243, 243A, 234, 247, 249, 5101, 5120, 5121 and 5122. 

Top and bottom opening is 3-1/2", bulge width is 4-1/2" and is 4-1/16" tall.

Has also been reported to fit Austromax “Aussie Bush Light” very well.

This is a used old Pyrex Bernz-o-matic globe. It is the same size as a Coleman 200A globe. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

This is a used USA made white letter replacement logo globe. Although used, it will be in good condition. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove. The green filler cap is shown for identification purposes only and is not included.

Pump Cup Neoprene for most lanterns

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.  Also fits the model 500 stove. Will have a new gasket installed.

Reproduction brass ball nut for the model 242 series lanterns. Look identical to the originals.

Reproduction cast aluminum pre-heater cup for the model 249 lantern. Some 249's came with this hard to find cup. Workmanship is excellent.

New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.

Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.

Burner tube for the model 249 lantern.

Reproduction brass vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.

This is a used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

Eccentric block for the model 249 lantern.

Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247 and similar lanterns.

This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

This is the longer style of the small valve stem packing. It is 3/8" long. The hole diameter is 3/16". Limited Supply.

Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

This is a reproduction white letter Germany made logo globe. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 241, 247, and 249.

New burner cap & screen for the model 236, 237 and 249 lanterns. 

Solid brass with stainless steel screen.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

This is a U.S. made early green sunrise logo globe used on lanterns from 1946 to 1962. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. The darkness of the green will vary from globe to globe. The printing was not done with the technology of printing in our current era. 

Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of dry leather.

Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

This is a new unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is not an original glass, but a straight sided globe with no markings of any kind. Glass measures 3 1/2" Wide X 4" Tall.