252 Milspec
-
Air Stem Old Style Long Used - E1358
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
-
252 Filler Cap Chain Bracket - S20
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
-
252 Direction Disk - S05
Direction disk for the military lanterns. These came out of the old SMP factory.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
Check Valve O Ring - S36
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
252 Quadrant Glass Pane Clear - E1540
Used clear quadrant glass pane for the milspec lantern. They are in excellent condition with no cracks. On some of them edges are slightly chipped as was common on these. The chipping is covered by the globe channels. They measure approximately 3 3/8 inches wide and 5 1/4 inches high.
-
Generator Nut - E1262
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
These came from the SMP factory when it closed down.
-
Generator Complete - E1274
This is a new old stock generator.
Fits Military model 252 lantern. Also other non Coleman military lanterns
-
Military specification Lantern Decals Set of 3 - D140
Replacement decals for All Military Lanterns ~ Set of Three Decals
-
Check Valve Milspec - S178
Reproduction check valve for the military lanterns. Will also fit the models 220/228B and 220/228C. Will not fit the later style lanterns.
-
252 Parts Well Cap NOS - E1280
New Old Stock - Parts well cap for the military lantern. Has a new rubber gasket.
-
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
-
SMP Milspec Decal One Piece - D167
Original one piece decals for the later SMP military lanterns. These are not reproductions. They came from the old stock of the factory when it closed.
-
Milspec Wrench - E1404
Original wrench for the military lanterns. This is the wrench only and does not have the secondary tip cleaner part.
-
-
Milspec Chain Ring - S02
This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one.
If your filler cap has a screw in the center of it then this gasket will not work.
The red filler cap is shown for illustration purposes only and is not included.
-
252 Collar - X1
Used collar for the milspec lantern. They have a few small spots of missing paint here and there.
-
Quadrant Glass Channel Used - E1424
Used Military Lantern globe channel. Crimps on burner frame to hold quadrant globe panes. May show sings of rust and wear.
-
252 Parts Well Cap Used - E1407
Used parts well cap for the military lantern. Will have a new gasket in it. Will show signs of rust and wear.
-
-
-
-
252 SMP Burner Frame Used
Used burner frame for a later Milspec lantern. This is a SMP (State Machine Products) Milspec burner frame.
-
252 Burner Used - E1565
This is a used Milspec burner. Will individually vary in wear and appearance.