282

Fits the model 200B, 282 and 285 lanterns. New generator includes new gas tip, spring, and tip cleaning wire. New part number is 3000005622.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

New Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Has gone in the past by part numbers 220C1401, and now 425A1405

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.

Fits 282, 286, 200B lanterns

Fits model 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns. 

Same as part number 206A1251

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits the fuel tube on the 550B stove.

New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 258, 286, and 288 model lanterns.

Pump Clip

Brand new Neoprene Pump Cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Pump Cup Neoprene for most lanterns

Used filler cap that fits most Coleman lanterns and stoves. Paint is chipped with a few wrench marks. 

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Knob for the 282, 286, 288, 290, 295, and 639 lanterns. May fit others also.

Used collar for the 282 and 285 model lanterns

Retainer with screws.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

Nut

This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. 

If your filler cap has a screw in the center of it then this gasket will not work. 

The red filler cap is shown for illustration purposes only and is not included.

Used frame bottom plate for the model 285 & 288A lantern

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This is a used 3 piece filler cap made of brass. Paint is worn and has a new filler cap gasket. Copper in color. Has wrench marks.

This is a used one piece filler cap. Paint is chipped or missing. Has a new gasket. 

Used collar for the 282 and 285 model lanterns

Used knob for the 282, 286, 288, 290, 295, and 639 lanterns. May fit others also.

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2.5" tall by 2" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss red in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.

Decal is 2" tall by 3.5" wide.

Instructions:

1. Pull off back side solid paper - pull at a sharp angle
2. Apply to clean and dry window or hard surface
3. Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
4. Carefully peel off clear plastic - also at a sharp angle

New frame bottom plate for the model 282, 285 & 288A lantern

This is a new old stock green 3 piece cap.  Excellent shape.