321C

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

This is a new Coleman made replacement pump cup  for all lanterns that came with the rubber style.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.

 O-Ring sizes are #6, #7, and #9, made of Flourosilicone.

We know it does work on these models: 533, 440, 442, 222, 222A, 222B, 226

Does not work on the 400B, 508B, 533A, 3024

Push on nut for end of pump rod. The small push on nut is used with leather pump cups.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Also known as part number 2000038026.

Pump Clip

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

New generator includes new gas tip, spring, and tip cleaning wire.

This fits the 321, 331 and the 335 models.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.

Universal pump assembly with leather cup that fits almost all Coleman lanterns and stoves. Does not fit the small Peak 1 lanterns or stoves, some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a new aluminum filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 242B5381.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Each one will vary in wear. 

Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. 

Wear and finish will vary. 

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  Comes with a new gasket that you will have to install.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket for you to install if needed.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is for one used 3 piece blue filler cap. Shade may vary.

Comes with a new gasket that you will have to install.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is for one used 3 piece filler cap. They are missing paint and in rough looking shape.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with one (photo is for illustration purpose only)

Comes with a new gasket for you to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Stud for 321 and  Peak 1 lanterns

For US addresses only. We will mail this check valve to you so you can change out your own check valve. This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
Please note that it will not work on a check valve that has been destroyed already or has had the air stem threads ruined. This tool will only work if it can be threaded into the air stem slot in the center of your old check valve. The tool must be installed correctly for it to work - using it while loose will cause the barrel tip to break off.

Initial cost is $100 with free shipping. If the tool return is postmarked within 10 days and it is returned with all the parts and is unbroken, we will refund $75 back to your initial payment card, resulting in $25 total cost plus whatever it costs for you to ship it back to us.

Look at the bottom of this listing for "Description". Click on that and you will see instructions for use with photos. 

C01 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

Used aluminum filler cap minus lanyard - in good shape.  Comes with a new gasket that you will have to install.