339

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

Push on nut for end of pump rod. The small push on nut is used with leather pump cups.

Used valve wheel screw.  Will be in good condition.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Also known as part number 2000038026.

Pump Clip

Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.

Fits model 339 lantern. New generator includes new gas tip, spring, and tip cleaning wire.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

Universal pump assembly with leather cup that fits almost all Coleman lanterns and stoves. Does not fit the small Peak 1 lanterns or stoves, some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This is a new aluminum filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Replacement needle for the 339 generator.

N.O.S Valve stem for the model 335 and 339 lanterns.

Has a small chip on the valve wheel.

NOS self tapping valve wheel screw.

For US addresses only. We will mail this check valve to you so you can change out your own check valve. This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
Please note that it will not work on a check valve that has been destroyed already or has had the air stem threads ruined. This tool will only work if it can be threaded into the air stem slot in the center of your old check valve. The tool must be installed correctly for it to work - using it while loose will cause the barrel tip to break off.

Initial cost is $100 with free shipping. If the tool return is postmarked within 10 days and it is returned with all the parts and is unbroken, we will refund $75 back to your initial payment card, resulting in $25 total cost plus whatever it costs for you to ship it back to us.

Look at the bottom of this listing for "Description". Click on that and you will see instructions for use with photos. 

C01 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.