621

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Has gone in the past by part numbers 220C1401, and now 425A1405

Push on nut for end of pump rod. The small push on nut is used with leather pump cups.

This is a used striped globe for the model 275. This globe will fit models 275, 275A, 621, 631A, 621B, 5114, 5114A, 5114B, and 5114C. It is approximately 5 1/4 inches tall. The large opening has approximately a 5 7/8 inch diameter. The smaller opening has approximately a 4 5/8 diameter. This globe is in good condition.

Reproduction generator nut for the 335 and 621 lanterns.

Pump Clip

This is a used one piece filler cap. Paint is chipped. Has a new filler cap gasket. These are green. The shade of green and wear varies within this stock of used caps. 

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. 

If your filler cap has a screw in the center of it then this gasket will not work. 

The red filler cap is shown for illustration purposes only and is not included.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This is a used one piece filler cap. Paint is chipped or missing in some spots. Gaskets have been replaced. 

Stud for 321 and  Peak 1 lanterns

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

New burner cap for 631, 635 and 639 lanterns. Solid brass with stainless steel screen.

This is a used one piece filler cap. Paint is chipped or missing. Has a new gasket. 

Used steel filler cap for Coleman lanterns. Has a new gasket and ready for use. 

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of dry leather.

USA made pyrex red letter replacement globe. This globe will fit models 275, 275A, 621, 631A, 621B, 5114, 5114A, 5114B, and 5114C. It is approximately 5 1/4 inches tall. The large opening has approximately a 5 7/8 inch diameter. The smaller opening has approximately a 4 5/8 diameter. Same size as the Canadian 880 globe.