635B

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

These Peerless mantles are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns. 

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.

Also known as part number 3000005094.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a new Coleman made replacement pump cup  for all lanterns that came with the rubber style.

This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

#11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.

Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".

This globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091

Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.

Knob for the 282, 286, 288, 290, 295, and 639 lanterns. May fit others also.

Valve assembly for 639 Kero lantern.

Compatible with 635 and the 621 series lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Coleman Canadian lantern generator G6 (635A297).

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is a new vent for the model 639 lantern. Coleman discontinued this part as of 2022

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

New burner cap for 621, 635 and 639 lanterns. Solid brass with stainless steel screen.

New fount for the model 635 & 639 lanterns. 

Used knob for the 282, 285, 286, 288, 290, 295, and 639 lanterns. May fit others also.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is for one used 3 piece blue filler cap. Shade and wear may vary.

Comes with a new gasket that you will have to install.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Burner tube for the later model 635 lantern. I believe it would also fit the later model 639 lantern too.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Collar and bolt for the model 635 and 639 lanterns.

Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.

Valve assembly for the model 635 lantern.

This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

NOS steel filler cap for Coleman lanterns. Comes in original packaging

NOS generator for the 639 and 635B Lantern. New generator includes new gas tip, spring, and tip cleaning wire.

Also known as part number 635-5891

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Silver in color. Includes a new gasket for you to install.