L327

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Fits models Air O lantern, 327, 427, Slant 220 lanterns and CQ lamps

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

This is a used collar for the model 327, 427, and similar lanterns. It may have spots of rust or other discoloration/ stains. 

Used burner frame for the 327 and 427 lanterns. This is a used item and will show signs of rust and wear.

Used gas tip for the Q99 generator and some Quick-Lite Lanterns and Lamps. Very tarnished

This is a used burner frame for the Quicklite lanterns. Actually for an early Air O Lantern. Portions are bent, but seems solid.

This is a used burner frame for the Quicklite lanterns. Note the lighting hole in the bottom, done well, but we don't think came with the hole from the factory.

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is a nickel plated brass burner tube. Not polished. More of a utilitarian type finish. For most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

Converts your standard size lamp or lantern filler plug hole so you can use a more modern lamp cap instead. No more having to have a crescent wrench. Screw this on in place of your filler plug. Fits Coleman CQ lamps, 327 lanterns, Air O Lanterns, and others with similar sized filler plug.

This is an original used globe made between 1936 to 1945 for Coleman lanterns that used the 220 size globe. Although used, it has been inspected for damage or defects (this one has a small bubble shown in picture) Please note that the green straight line logo used on these globes was very lightly stamped and can sometimes be difficult to see. This was normal for the time period. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Reproduction vent bushing for the Air O Lantern, model 327, or 427 lantern. Will work on any older Coleman lantern that took a nickle plated brass vent. Now you can repair that old 2 piece vent and put it back together again correctly. Slightly peen over the ends of the new bushing to hold everything together.

Used burner assembly for the old model 227, 327,427, and Air O Lite lanterns. Will also work on CQ lamps and other lamps that would have originally taken the Q99 generator.

Used burner frame for the 327 and 427 lanterns. This is a used item and will show signs of rust and wear.

Vent rod for the Quick-Lite lanterns. It is 1 1/4 inches long.

Used burner frame for the L227 Quick-Lite, 327 and 427 lanterns. This is a used item and will show signs of rust and wear.

Used baffle plate for the old Quick-lite type lanterns. It will show signs of use and will vary in wear.

Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.

This is a used vent for a Quick-Lite Lantern model 227, 327, and 427.

Has a few dents.

This is a used fount for the Quicklite model 327 lantern. It is undated from what we can see. Needs a bit of elbow grease to look good again, but there are no visible dents.

Used valve assembly for the Quicklite model 327 and 427 lantern. They all vary in wear and some valve wheels may be cracked.

A new packing has been installed.

Reproduction filler plug for the old Quicklite lanterns and lamps. Made of solid brass. Now you can replace your old rounded off filler plug. Made to use the 427 gasket rather than the old lead gasket. Will come with the new gasket.

Lead gasket used on the filler plugs of old Quicklite lanterns, lamps and some stoves.

New Old Stock Air stem / thumb screw for filler plugs used on the old Quicklite lanterns and lamps. These are all brass. None have any nickle plating on them.

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

Steel body Q77 generator. Probably made during WWII or possibly even WW1. New old stock but very tarnished from age.

Quick Clip mantles. Same size as Coleman 21A mantles.

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

Used fount for the model 327 Quicklite lantern. Date is 9-11.

Has a couple dents. 

Used fount for the model 327 Quicklite lantern. Has no date. Has a few dings, but seems like it is solid and would clean up well.

Used fount for the model 327 Quicklite lantern. This is undated and needs a little work to look beautiful. 

Used figure 8 piece as used on the old Q style burner.

Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.

German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Reproduction valve stem bushing for the 327 and 427 Quicklite lanterns.

Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket.

Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.