L427
-
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
-
Cap Gasket - S56
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
-
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
427 Pump Cup - S82
Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point.
A fellow collector has shared with us that it will also fit the Akron 107 with a built on pump.
-
Mantle String Tie #21 2 pack - M03
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
-
-
Q99 Reproduction - R401
Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.
-
Brass T-Handle Pump Reproduction - R315
This is a new production T-handle pump. It works great to pressurize your lantern, lamp, or Handy Gas Plant. Approximately 10 inches long.
-
Tip Cleaning Needle Tool - S180
Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.
-
Check Valve Old Style - S179
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
-
327 Vent Bushing - S161
Reproduction vent bushing for the Air O Lantern, model 327, or 427 lantern. Will work on any older Coleman lantern that took a nickle plated brass vent. Now you can repair that old 2 piece vent and put it back together again correctly. Slightly peen over the ends of the new bushing to hold everything together.
-
Burner Tube Brass 2 7/8 - E1264
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
-
-
427 Filler Cap Insert - S154
Reproduction filler cap insert for the older winged style filler caps used on model 427 lanterns. Comes with the new gasket.
-
220 Globe Green Sunrise Logo - G24
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
-
220 Globe White Letter Germany - G05
German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Air Stem Old Style Long Used - E1358
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
-
Burner Tube Short - S132
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
-
220 White Logo USA Globe - G63
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Burner Tube 2 1/2 Inch - E1471
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
-
327 Valve Stem Bushing - S168
Reproduction valve stem bushing for the 327 and 427 Quicklite lanterns.
-
220 Red Logo Pyrex Globe USA - G28
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
-
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
-
Gas Tip - GT11
Used gas tip for the Q99 generator and some Quick-Lite Lanterns and Lamps. Very tarnished
-
220 White Logo USA Globe - G44
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
-
Pump Assembly, 220B Thin Brass Cap, Used - E1420
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
-
Air Stem Reproduction - S124
This is a reproduction air stem for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.
-
Burner Assembly Used Old Style - E1356
Used burner assembly for the old model 227, 327, 427, and Air O Lite lanterns. Will also work on CQ lamps and other lamps that would have originally taken the Q99 generator.
-
Air Stem Long New Style - E1048
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
-
Burner Tube Steel Old Style - E1101
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
-
Burner Tube Brass 2 3/4 - E1129
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
-
427 Check Valve Ball - E1021
This is the small check ball for the 427 lantern with an external pump. In the photo below, you can see the application. These are made from 440C Stainless Steel, the original was brass.
-
-
220 Pyrex Amber Globe - G669
This is a replacement amber globe. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Globe is stamped with "Made in U.S.A."
-
Filler Cap Scalloped Winged Used - E1098
This is a used scalloped edge winged filler cap that was used on the model 427 and other Quick-Lite lanterns with the pump that was mounted to the fount. It will show signs of nickel loss and some light wrench marks - will vary in wear. Comes with a new gasket installed.
-
220 Globe Sears Logo - G59
This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Pump Assembly, 220B Thick Brass Cap, Used - E1390
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick. Has a nickel plated brass cap.
-
Used Burner Frame #1
Used burner frame for the 327 and 427 lanterns. This is a used item and will show signs of rust and wear.
-
Pump Brass Cap NOS - E1123
New old stock long pump for the model 220B and 220C lantern. These have a brass cap that connects the pump to the lantern. They have new pump leather on them. Probably made in the 1930's or early 40's.
-
220 Red Logo Replacement Globe USA - G65
This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
-
Mixing Chamber Used with Vent Rod - E1001
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
-
Valve Assembly Quicklite Used - E1433
Used valve assembly for the Quicklite model 327 and 427 lantern.
-
Guillotine 220 Carry Case - CC7
Used guillotine carry case for all small hat 220 style lanterns. Will also fit 290, 295, 427, 327, and small hat Sears lanterns.
This one has a bit of rust and some small dents (see photos)