242A

Most Popular Sized Mantles and are treated with Thorium from the factory. 4 mantles per pack. Use on these models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Will fit all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

New Coleman made Spark Igniter. Comes in new packaging with instructions.

This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242  and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

This is a new Coleman made replacement pump cup  for all lanterns that came with the rubber style.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

Used generator nut for many Coleman models. These are in fine shape, just dirty.

New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.

New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".

New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Top and bottom outer diameter is 3.25" and height is 4.25"

Also known as part number R690B051.

Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.

Handy little part invented by a lantern collector. Replaces the fuel and air tube on a model 200A lantern to a straight pick up tube for kerosene. Just remove the fuel tube and screw on. Also fits a 242 series lantern.

New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.

Solid brass with stainless steel screen.

New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.

Stainless Steel burner frame to valve nut for the 200, 200A, 201, 202, 222, 222A, 222b, 237A, 237B, all the 242s, 321B, 325A, 331, 335, 339, 621A, 621B and 635 lanterns. May also fit other models and some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Also listed in diagrams as part number 604A456.

This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.

Reproduction check valve for 242, 242A, 242K, 243 and 243A lanterns. This is the re-buildable type check valve for early single mantle lanterns that did not use an air stem. Will not work with others.

Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

Zippo brand Flints for the Coleman Lantern Spark Igniter.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.

Reproduction generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.

Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.

Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 242 lanterns
• 1 Generator for the 242 lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket specific to the 242 - for the bottom of your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 242 HERE
• 242A HERE
• 242B HERE
• 242C HERE

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a reproduction generator for 200, 200A, 202, 234, 242, 243, 246 & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Same as the old part numbers T66, 200A2891 and 3000005089.

This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.

This is a 10 PACK of gaskets for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

New reproduction pump cup assembly for 242 NL (No Letter), 242A , 242K, 243 , 246 and or any Coleman lantern or stove from the early 30's with a solid pump stem with no air hole in the middle. These are made for the USA manufactured Coleman pump shafts and will fit as they should. If yours is made in Canada, you will have to use a small file to widen the brass center to a cone shape to match your pump shaft - see the photos. Also known as part number 233-518

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.