476.72211

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Most Popular Sized Mantles and are treated with Thorium from the factory. 4 mantles per pack. 

Use on these models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Will fit all Coleman Lamps. 

These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a new generator made by Coleman for 200, 200A, 242, 243, 202 & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Same as the old part numbers T66, 200A2891 and 3000005089.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. Also known as part number 3000005094.

This is a new Coleman made burner cap for the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

Also known as part number 242J5201.

Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Reproduction Generator Spring. These will fit inside the generator tube of a 200, 200A, 242, 243, 202, Similar Sears Lanterns and may fit others.

Used generator nut for many Coleman models. These are in fine shape, just dirty.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 234, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.

Also known as part number 242-353.

Pump Clip

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Top and bottom outer diameter is 3.25" and height is 4.25"

Also known as part number R690B051.

Reproduction needle assembly for the 200A2891 T66 generator used on lantern and lamp models 121, 200, 200A, 202, 242, 242B, 242C, 243, 476.72211 & 476.74550.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style. 

In the 426 stove series, this only fits 426 or 426A

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

200A Burner Tube

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

NOS fuel and air tube for the model 200 and 242 series lanterns and also fits the 530 pocket stove.

This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.  

Comes with a new gasket that you will have to install.

Lock Nut for the 200A lantern. Goes on the top end of the burner tube.

Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.

New reproduction burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.

Solid brass with stainless steel screen.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

New reproduction generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns.

Stainless Steel burner frame to valve nut for the 200, 200A, 201, 202, 222, 222A, 222b, 237A, 237B, all the 242s, 321B, 325A, 331, 335, 339, 621A, 621B and 635 lanterns. May also fit other models and some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Also listed in diagrams as part number 604A456.

Used bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.

This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 200-6381 and without the air stem.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.