476.72212

This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

Reproduction shorter fuel and air tube for the double mantle Sears lanterns made by Coleman.

Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.

This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is a used mixing chamber. May or may not have a vent rod and air tube screw.

Used Pump Assembly Spring

Spring ONLY

This is a used older style brass mixing chamber for the 220-228 series lanterns.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

Newer style mixing chamber for the model 220/228 lanterns. 

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

This is an original used old stock amber globe. Some of these globes have the light blue band around the top and bottom of the globe as is common with the old ones. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Globe is stamped with "Made in U.S.A."

This one looks like it's had some good use - faded and a little dirty (see photo)

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

Used burner frame that will fit models 220B through early 220F through approximately 1971.

This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.

Used Sears carry case for double mantle Sears Lanterns including models 476.72212, 476.72213, 476.74060, 476.74070. Has the insert that will allow 220/228's to fit as well.

Great condition - looks like it hasn't been used very much if at all - all latches work great and handle is also in great shape. Has a few small scratches and paint chips from moving around over the years (see photos)

This product is not included in the OCP free shipping program. 

Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.

Used Sears fount dated 3-66. 

It's in pretty good shape just has some scuffs and minor scratches. 

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

Used closed ball nut.

Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

Fuel Cap with pressure gauge.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

Used, black filler cap with lanyard - in good shape. Comes with new lanyard.  Comes with a new gasket that you will have to install.

This is a used one piece filler cap off the Model 200A burgundy. 

Comes with a new gasket that you will have to install.

New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.