476.72212

Products: 150 of 67
Show: 50
  • Peerless Mantles 2C-HG - M1

    Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

    Score: 5.00 (votes: 3)
    Reviews: 3
    |
    3
    • $5.65
  • Leather Pump Cup - S81

    This is the common Coleman pump cup that fits most lanterns and stoves. 

    Has a 7/8 inch diameter and is made of oiled leather.

    Score: 3.33 (votes: 3)
    Reviews: 3
    |
    3
    • $3.75
  • Check Valve With Stem - C1

    This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. The latest part number for this is 2006381ZCL.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $9.40
  • Large Valve Stem Packing - P1

    Typically used to stop a fuel leak from the valve stem on older appliances.

    This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

    If you need to check your model, please see the PARTS DIAGRAM PAGE

    425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

    Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

    Made of 100% graphite.

    Not rated yet
    • $3.55
  • Mantle String Tie #21 4 Pack - M2

    Coleman's Most Popular Sized Mantles. 4 mantles per pack

    Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

    Not rated yet
    • $7.00
  • New Filler Cap Brass - C4

    New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

    Has gone in the past by part numbers 220C1401, and now 425A1405

    Not rated yet
    • $9.60
  • Mantle String Tie #21 2 pack - M3

    Coleman's Most Popular Sized Mantles. 2 mantles per pack

    Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

    Not rated yet
    • $3.75
  • 220 Globe Clear - G4

    This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. New part number 2000026613.

    Not rated yet
    • $17.90
  • Ball Nut - S9

    New Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

    Not rated yet
    • $3.25
  • Pump Clip Used - S17
    • Free Shipping

    Pump Clip Used - S17

    Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

    Not rated yet
    • $1.65
  • 220 Filler Cap Insert - S144

    This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

    Not rated yet
    • $9.85
  • Generator Nut - S176

    Generator nut.

    Not rated yet
    • $5.85
  • Screw Flat Head - S71

    Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.

    Not rated yet
    • $0.25
  • Used Generator Nut - S26

    Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

    Not rated yet
    • $2.15
  • Ball Nut Used - S18

    Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

    Not rated yet
    • $3.00
  • Screw Phillips Head - S74

    Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.

    Not rated yet
    • $0.25
  • Pump Clip - S22
    • Free Shipping

    Pump Clip - S22

    Pump Clip

    Not rated yet
    • $3.25
  • Pump Assembly Leather Used Square Nut - E264

    This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    Not rated yet
    • $13.55
  • Valve Wheel Black Old Style Used - S79

    This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.

    Not rated yet
    • $11.50
  • Air Stem Used Old Style - S31

    Air stem older style used. Has the larger head on the end.

    In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

    Not rated yet
    • $4.90
  • Eccentric Block - S137

    Eccentric Block

    Not rated yet
    • $7.60
  • Black Valve Wheel New Style USED - S78

    This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A

    Not rated yet
    • $9.00
  • Filler Cap Tire Valve Brass - R302
    • New!

    Filler Cap Tire Valve Brass - R302

    This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

    Not rated yet
    • $13.20
  • Filler Cap Tire Valve Nickel - R301
    • New!

    Filler Cap Tire Valve Nickel - R301

    This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

    Not rated yet
    • $13.90
  • Tip Cleaner Stem Reproduction - R606

    This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.

    Not rated yet
    • $10.60
  • Vent Rod 220 Long - S151

    Longer vent rod for models 220/228B through 220/228E and 235.

    Not rated yet
    • $6.85
  • Burner Tube Brass 2 7/8 - E36

    Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

    Not rated yet
    • $4.35
  • 220 Red Logo Replacement globe USA - G22

    This is a US made replacement globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

    Not rated yet
    • $26.05
  • 220 Globe Green Sunrise Logo - G24
    • New!

    220 Globe Green Sunrise Logo - G24

    This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

    The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

    This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

    Not rated yet
    • $35.00
  • 220 Globe White Letter Germany - G90

    German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

    Not rated yet
    • $20.90
  • Filler Cap 3 Piece Green Used - E383

    This is for one used 3 piece filler cap with a newly installed gasket. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.

    Not rated yet
    • $13.00
  • Pump Assy Leather Used Push On Nut - E263

    This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

    Not rated yet
    • $11.95
  • Burner Tube 2 1/2 Inch - E32

    Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
    Not rated yet
    • $5.40
  • Burner Tube Short - S132

    Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

    Not rated yet
    • $7.00
  • Needle Assembly Used - S8

    Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

    Not rated yet
    • $4.50
  • Valve Wheel Black Square Hole Used - E76

    Used valve wheel for 201, early 220B's and some model 236 & 237's. In the 426 stove series, this only fits 426 or 426A It fits on valve stems with a square shaft end. It is not interchangeable with other wheels. Will vary in wear.

    Not rated yet
    • $10.85
  • Burner Tube Nickel Plated

    This is a nickel plated brass burner tube. Not polished. More of a utilitarian type finish. For most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

    Not rated yet
    • $7.60
  • Filler Cap Green Used - E258

    This is a used one piece filler cap. Paint is chipped. Has a new filler cap gasket. These are green. The shade of green and wear varies within this stock of used caps. 

    Not rated yet
    • $10.85
  • Used Generator Spring - S29

    Used generator spring for 220, 228, 275 lanterns. Also fits some Sears models.

    Will show signs of use but will be in good shape.

    Not rated yet
    • $7.05
  • Ball Nut Splined Used- S3

    Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

    Not rated yet
    • $4.60
  • Fuel Air Tube Reproduction - S122

    Reproduction shorter fuel and air tube for the double mantle Sears lanterns made by Coleman.

    Not rated yet
    • $14.10
  • Air Stem New Style Used - E470
    • New!

    Air Stem New Style Used - E470

    Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

    Not rated yet
    • $0.25
  • Filler Cap 3 Piece Nickel Plated Used - E349

    This is for one used 3 piece filler cap with a newly installed gasket. They are in various stages of wear. Finish is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.

    Not rated yet
    • $16.25
  • Mixing Chamber New Style Plated - E189

    This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar.

    Not rated yet
    • $4.35
  • 220 Red Logo Pyrex Globe USA - G28

    This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

    Not rated yet
    • $26.60
  • Mixing Chamber New Style Brass - E328

    Newer style mixing chamber for the model 220/228 lanterns. 

    Not rated yet
    • $8.15
  • Burner Tube Brass 2 3/4 - E448

    Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

    Not rated yet
    • $4.35
  • 220 White Logo USA Globe - G91

    USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

    Not rated yet
    • $21.95
  • Burner Tube Steel Old Style - E114

    Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

    Not rated yet
    • $4.35
  • 908M Mantles - E92

    Quick Clip mantles. Same size as Coleman 21A mantles.

    Not rated yet
    • $4.35
Products: 150 of 67
Show: 50