476.72213

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Most Popular Sized Mantles and are treated with Thorium from the factory. 4 mantles per pack. 

Use on these models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Will fit all Coleman Lamps. 

These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

New Coleman made generator for 220, 228, 275, and similar Sears lanterns. The new generator includes new gas tip, spring, and tip cleaning wire.

Will fit Coleman Lanterns: 220 B thru 220 K, 228 B thru K, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070

This is the same generator as the old part number T44 and same as new part number 3000005090.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. Also known as part number 3000005094.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

Also known as part number 242J5201.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Used generator nut for many Coleman models. These are in fine shape, just dirty.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.

Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.

This also works well as part number 335-0604 used on the burner frame/tube for the 335 lantern.

Pump Clip

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style. 

In the 426 stove series, this only fits 426 or 426A

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A

New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.

This also fits the AGM 2572 & Kamplite RL-3 

Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. If your lantern diagram calls for part number 220E5891, this is what you need.

Longer vent rod for models 220/228B through 220/228E and 235.

These are used leather pump cups that fit most lanterns and stoves. They may need some oil and conditioning, but are still flexible. This is the typical sized 7/8" pump cups for most lanterns and stoves.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 200-6381 and without the air stem.

Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.

Will show signs of use but will be in good shape.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

Used body of the 220B3571 tip cleaner assembly. Will show signs of wear.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.

These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.

Single Ball Nut. Fits all Coleman lanterns except the 242 type models. In good shape - just dirty.

This is a used pump square nut.

Comes with one square nut ONLY.

NOS, USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

New old stock T44G generator. This is the early version of the 220E5891 generator. Instead of a cardboard tube it has a cloth material over the spring. These show a bit of tarnish from being on the shelf for 80 years.

Will fit Coleman Lanterns: 220 B thru 220 J, 228 B thru J, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070

The original box is not included - just showing as an example of the original packaging. 

One generator is included.