413D
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
New Filler Cap Brass - C04
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Also known as part number 425A1405.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
Leather Pump Cup And Back-Up Plate - C05
Leather pump cup, push on nut and back-up plate.
Also known as part number 3000005094.
-
Valve Wheel Screw - S72
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.
-
Graphite Ribbon - P09
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
-
Pump Clip Used - S17
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
-
Check Valve O Ring - S36
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
-
-
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Valve & Generator - C33
New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980
-
-
Screw Flat Head Steel - S70
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
-
-
Filler Cap Green Used - E1248
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.
-
Filler Cap Dark Gray Used - E1307
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Dark gray in color like the new production Duel Fuel models.
Comes with a new gasket for you to install.
-
Filler Cap 3 Piece Red Used - E1372
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
-
-
Filler Cap Light Gray Used - E1208
Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket that you will have to install.
-
Block and Needle Assembly - E1109
Block and Needle Assembly. Measures approximately 4 1/4 inches long.
-
Filler Cap Brass Used - E1210
This is a used one piece filler cap. Each one will vary in wear. Comes with a new gasket that you will have to install.
-
Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a screw in the center then these gaskets will work. Red 3 piece filler cap show for demonstration purposes only.
-
-
Large Valve Stem Packing - 10 PACK - P01
This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Stove Handle Used - E1249
Used stove handle for many stove models. If your handle looks like this, it probably will fit since there is only one size Coleman made in this design. Will show signs of rust and wear.
-
Valve & Generator - E1514
Used valve, generator, spring, needle, gas tip and pick up tube. Valve and stem turn as they should. Needle passes through the gas tip in the off position. These were taken of of used stoves, but we cannot guarantee they will work without being cleaned up and worked over. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980
-
Stove Leg - SL2
Used Stove leg for models 413D and 413E. Will have rust due to age and storage over the years.
-
Leather Pump Cup - 10 PACK - S81
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves. Has a 7/8 inch diameter and is made of oiled leather.
-
-
Stove Handle Used - E1008
This is a used handle for many Coleman stoves.
It measures 5 13/16 inches across. It will show signs of rust and wear.
-
-
Stove Handle Used - E1203
This is a used stove handle for the model 413H stove and many others. It measures 5 3/4 inches across. Will show signs of rust and wear.
-
Filler Cap Dark Green Used - E1431
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with one (photo is for illustration purpose only)
Comes with a new gasket for you to install.
-
Stove Tank Red Used - ST2
Used tank for the model 413C - 413F, and 442 & 442A stove. This is the late production, red colored.
-
Valve Stem Complete less Needle and Holder - E1518
These are new old stock and have a bit of rust on them from sitting on a shelf for decades. Comes with a packing from the factory. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle. If your stove has been updated to a later valve style then this would not fit.
The needle and holder for this is part number 471-2381 HERE.
A whole new valve and gen would be part number 413B6601. That is the valve that fits the 413E and 413G stoves.
-
Used Valve Stem Complete less Needle and Holder - E1010
These are Used and have a bit of rust on them. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle. If your stove has been updated to a later valve style then this would not fit.
The needle and holder for this is part number 471-2381 HERE.
A whole new valve and gen would be part number 413B6601. That is the valve that fits the 413E and 413G stoves.