413E

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Also known as part number 425A1405.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Leather pump cup, push on nut and back-up plate. 

Also known as part number 3000005094.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Fits models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. New generator includes new gas tip, spring, and tip cleaning wire.

Also known as part number 3000005106.

Pump Clip

Used valve wheel screw.  Will be in good condition.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980

Lighting stem.

Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443  Instant Light, 2 & 3 Burner Stoves

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.

Fuel Air Tube

These are used leather pump cups that fit most lanterns and stoves. They may need some oil and conditioning, but are still flexible. This is the typical sized 7/8" pump cups for most lanterns and stoves.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Universal pump assembly with leather cup that fits almost all Coleman lanterns and stoves. Does not fit the small Peak 1 lanterns or stoves, some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

Generator Coil. Rusty. 

Fits 426B, 426C, 413E, 413F, 442, 442A and 443 stoves.

Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

This is a new aluminum filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243 and similar lanterns or the 500 stove.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

Block and Needle Assembly. Measures approximately 4 1/4 inches long.

This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Used Burner Cap, Bowl, Rings and Bolt. Used but in good shape.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves. Has a 7/8 inch diameter and is made of oiled leather.

Used Stove leg for models 413D and 413E. Will have rust due to age and storage over the years. 

This is a used handle for many Coleman stoves.

It measures 5 13/16 inches across. It will show signs of rust and wear.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is a used stove handle for many stoves. 

It measures 5 13/16 inches across. Will show signs of rust and wear.

It is know for sure to fit the 413E and a 425C. 

This is for one used 3 piece blue filler cap. Shade may vary.

Comes with a new gasket that you will have to install.

Manifold pipe. It is 10 inches long.

This is a used stove handle for the model 413H stove and many others. It measures 5 3/4 inches across. Will show signs of rust and wear.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with one (photo is for illustration purpose only)

Comes with a new gasket for you to install.