425

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Used Burner Cap, Bowl, Rings and Bolt. Used but in good shape.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

New Filter Funnel For Lamps And Stoves. 

Stops filling your lantern or stove at the correct level.
This funnel is new and unused.

Needle And Block Assembly

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket NOT installed.

This is a used one piece filler cap. Each one will vary in wear.

Comes with a new gasket - not installed

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a screw in the center then these gaskets will work. 

Red 3 piece filler cap show for demonstration purposes only.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear.

Comes with a new gasket.

Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. 

Comes with a new gasket - not installed

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Fuel and Air Tube. Same as part number 425-6461.

New Coleman made generator includes new gas tip, spring, and tip cleaning wire. This will fit models: 425, 425B, 425C, 425D, 425E, 425F, Sears 476.72301 & 476.74960.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

Lighting stem.

Manifold pipe. It is 8 inches long.

Used Manifold pipe for the model 425, 425B, and 425C stove. Bit dirty, but in good shape.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Has gone in the past by part numbers 220C1401, and now 425A1405

New old stock nickel plated one piece cap. The ones I have left do not come in a package. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

NOS metal pump cap for pump assembly

Does not come with whole assembly

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Pump Clip

Pump Cup Neoprene for most lanterns

Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

This is a used handle for many Coleman stoves.

It measures 5 13/16 inches across. It will show signs of rust and wear.

Used 425B1651 tank for the model 425 stove. Fits Models 425, 425B, 425C, 425D, 425E, 425F and may fit other models.

Will not work on the early 425 no letter with original round tank. 

Used copper colored tank for the models 411, 411A, 6J, 4M, 4K, 421, 421A, and 421D stoves.  Has paint chipping and scratches - see photos. Seems solid. Comes with pump assembly, filler cap and valve/generator. The generator/valve will be rotated 1/4 turn counterclockwise for shipping purposes. You will need to tighten it by that much to use it.

Has not been tested or worked on, but the tank does pump up and hold pressure - the generator may or may not work.

Used 425B1651 tank for the model 425 stove. Fits Models 425, 425B, 425C, 425D, 425E, 425F and may fit other models.

Will not work on the early 425 no letter with original round tank. 

Used 425B1651 tank for the model 425 stove. Fits Models 425, 425B, 425C, 425D, 425E, 425F and may fit other models.

Will not work on the early 425 no letter with original round tank. 

Used 425B1651 tank for the model 425 stove. Fits Models 425, 425B, 425C, 425D, 425E, 425F and may fit other models.

Will not work on the early 425 no letter with original round tank. 

Used 425B1651 tank for the model 425 stove. Fits Models 425, 425B, 425C, 425D, 425E, 425F and may fit other models.

Will not work on the early 425 no letter with original round tank. 

New Coleman made valve and generator. This part will fit: 2G, 2H, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 425, 425B, 425C, 425D, 425E, 425F and Sears 476.72301, 476.74960.

Valve minus the generator. Use part 412A6511 to make a complete valve assembly.

Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.

Valve minus the generator for the model 425 series stoves.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.

Used RED valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.

Used valve wheel for Coleman stoves. Has the hollow style backside as was common on the later stoves. Completely interchangeable with valve wheel 412-2491.

Used valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.