425C
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Small valve stem packing - P2
This is the smaller size of the valve stem packing. It is 5/16" long. The hole diameter is 3/16". It would be used on the old 327 Quicklites, 427 lanterns and early CQ lamps. It would also be used on irons and some lanterns with the smaller diameter valve stem. Also fits the early pre-425F stoves. The 425F and later uses the larger packing. We are showing three in the picture so you can see it from all angles. They are sold one at a time. Made of 100% graphite.
-
Leather Pump Cup And Back-Up Plate - C6
Leather pump cup, push on nut and back-up plate. New part number 3000005094.
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
New Filler Cap Brass - C4
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Has gone in the past by part numbers 220C1401, and now 425A1405
-
Valve Wheel Screw - S72
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-058 is needed.
-
-
Generator Stove - C12
Fits the model 425 two burner stove. New generator includes new gas tip, spring, and tip cleaning wire.
-
-
-
-
-
-
-
-
Filler Cap Tire Valve Nickel - R218
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Brass - R236
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Stove Grate Used 425E Rusty - SG5
This is used stove grate for the model 425E stove but it has some rust.
-
-
-
Screw Flat Head Steel - S70
Steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves.
-
Filler Cap Red Chipped - E91
Used filler cap that fits most Coleman lanterns and stoves. Paint is chipped with a few wrench marks.
-
Pump Assembly Leather Used Square Nut - E981
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
Pump Clip Used - S17
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
-
Stove Handle Used - E184
This is a used stove handle for many stoves.
It measures 5 13/16 inches across. Will show signs of rust and wear.
It is know for sure to fit the 413E and a 425C.
-
Stove Handle Used - E146
This is a used handle for many Coleman stoves.
It measures 5 13/16 inches across. It will show signs of rust and wear.
-
Graphite Ribbon - P9
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
-
Valve Assembly Small Stem - E196
Same as the other 412-6561 valve assembly except it has the smaller diameter valve stem as found on the earlier than 425F stove models.
-
Push On Nut Large - S1
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
-
-
Small Valve Stem Packing Long - P7
This is the longer style of the small valve stem packing. It is 3/8" long. The hole diameter is 3/16". Limited Supply.
-
Air Stem New Style Used - E470
Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.
-
Filler Cap 3 Piece Used Copper Color - E729
This is a used 3 piece filler cap made of brass. Paint is worn and has a new filler cap gasket. Copper in color. Has wrench marks.
-
Filler Cap Red Used - E835
This is a used one piece filler cap. Paint is chipped or missing. Has a new gasket.
-
Valve Assembly Small Stem - E504
Found on the earlier than 425F stove models. Use part 413A6531 to make a complete valve assembly.
-
Pump Assy Leather Used Push On Nut - E965
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
-
-
Manifold Pipe - E41
Used Manifold pipe for the model 425, 425B, and 425C stove. Bit dirty, but in good shape.
-
Coleman Filter Funnel - C82
New Filter Funnel For Lamps And Stoves.
Stops filling your lantern or stove at the correct level.
This funnel is new and unused. -
-
-
Stove Tank - #17
Used red tank for the model 425E stove. Will not work on the early 425 no letter with original round tank.
Paint chipping and rust but seems solid. Will eventually need a new paint job.
-
Valve Minus the Generator, Used - E63
Used valve minus the generator for the model 425 series stoves. These have not had service and may or may not need a new graphite valve packing. HERE is the packing for this model, it uses the P2 packing.
-
Window Decal - Lantern Green - D101
Window decal for glass or a hard surface - gloss green in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal - Lantern White - D103
Window decal for glass or a hard surface - gloss white in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle
-
Window Decal Lantern - Flat Black - D104
Window decal for glass or a hard surface - flat black in color. Can also be used on any hard surface - laptop, toolbox, water bottle, etc.
Decal is 2.5" tall by 2" wide.
Instructions:
- Pull off back side solid paper - pull at a sharp angle
- Apply to clean and dry window or hard surface
- Apply pressure through front clear plastic with a credit card making sure it is adhered well to the new surface
- Carefully peel off clear plastic - also at a sharp angle