Reproduction filler cap gasket for Coleman 3-piece fuel caps. Fits most Coleman lanterns and stoves that use the standard 3-piece cap with the center bolt. Good fit & quality replacement that helps stop fuel leaks. Red cap shown for reference only.
Look HERE for how to install these.
Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.
Also known as part number 425A1405.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.
Also known as part number 3000005094.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
New Coleman-manufactured pump cup designed for all lanterns that originally utilized the rubber-style cup.
Also known as part number 639-1091.
New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.
Also known as part number 242J5201.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Used, round headed valve wheel screw. Will be in good condition. These fit many models. Over the years, they changed the types of screws to hold on valve wheels. Please compare how this looks to yours if ordering. These will not fit the 236 or 237.
10-pack of reproduction filler cap gaskets for Coleman 3-piece fuel caps (S41). Ideal for many Coleman lanterns and stoves using the standard size cap with center bolt. Smart way to keep spares on hand and keep your gear leak-free. Red cap shown for reference only.
Look HERE for installation instructions.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.
Comes with a new gasket that you will have to install.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.
Fits models requiring part numbers 200-6381, 400-6381, 242B5381, or 621-5361.
New Coleman-manufactured filter funnel designed for lanterns and stoves.This funnel features a specific design that automatically stops the filling process once the fuel reaches the correct level, preventing overfilling.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
Also known as part number 1062-1613.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket for you to install if needed.
Original NOS Coleman Graphite Packing.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Used, round headed valve wheel screw. Will be in good condition. These fit many models. Over the years, they changed the types of screws to hold on valve wheels. Please compare how this looks to yours if ordering. These will not fit the 236 or 237.
Also known as 425-175
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically, this is used on the old 327 QuickLites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
This decal is for the Coleman Model 425E stove. It calls out the 412-5621 generator which is also used on models 425, 425B, 425C, 425D, and 425F stoves. We placed this on a black background so you can read the text. Very nice decal with proper dimensions.
When you buy this decal with free shipping, we’ll send it in a stamped envelope via USPS mail. It will ship within 1 business day and arrive within standard USPS delivery times for a regular letter.
Used Pump Assembly Spring
Spring ONLY
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
This is used check valve, the ball moves freely, but these have not been tested.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
If your part diagram calls for the 242B5381, 200-6381 or a 621-5361 check valve then this would be the correct part. Also known as part number 2006381ZCL.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.
These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
