442A
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. If your filler cap has a screw in the center of it then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
-
Check Valve With Stem - C01
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part.
Also known as part number 2006381ZCL.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Cap Gasket - S56
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as cap gasket 118B1361 but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
-
New Filler Cap Brass - C04
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Also known as part number 425A1405.
-
Pump Clip Used - S17
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
-
Check Valve O Ring - S36
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
Generator Stove - C30
Fits models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005106.
-
-
-
Air Stem Used Old Style - S31
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
-
O-Ring - S37
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits the fuel tube on the 550B stove.
-
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Valve & Generator - C33
New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980
-
-
Auxillary Burner Bowl and Rings - C53
Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443 Instant Light, 2 & 3 Burner Stoves
-
Valve Wheel Red Old Style Used - S77
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
-
Pump Plunger - C37
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203.
-
Screw Flat Head Steel - S70
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
-
-
Filler Cap Green Used - E1248
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.
-
Filler Cap Dark Gray Used - E1307
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Dark gray in color like the new production Duel Fuel models.
Comes with a new gasket for you to install.
-
Filler Cap 3 Piece Red Used - E1372
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
-
Air Stem New Style Used - E1250
Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.
-
Generator Coil - E1345
Generator Coil. Rusty.
Fits 426B, 426C, 413E, 413F, 442, 442A and 443 stoves.
-
Filler Cap Light Gray Used - E1208
Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket that you will have to install.
-
Block and Needle Assembly - E1109
Block and Needle Assembly. Measures approximately 4 1/4 inches long.
-
Filler Cap Brass Used - E1210
This is a used one piece filler cap. Each one will vary in wear. Comes with a new gasket that you will have to install.
-
Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a screw in the center then these gaskets will work. Red 3 piece filler cap show for demonstration purposes only.
-
-
Filler Cap Gasket for 1 Piece Cap - 10 PACK - S42
This is a 10 PACK for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. If your filler cap has a screw in the center of it then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
-
Burner Cap & Fillers - E1496
Used master burner bowl, cap, bolt and fillers - bit dirty, but in good shape.
-
Large Valve Stem Packing - 10 PACK - P01
This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Stove Generator Used - E1442
Used generator includes gas tip, spring, and tip cleaning wire. This will fit models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. Over the years Coleman changed the outer tube of the generator, but all are compatible with the above models. Yours may be any style shown in the second photo.
-
Valve & Generator - E1514
Used valve, generator, spring, needle, gas tip and pick up tube. Valve and stem turn as they should. Needle passes through the gas tip in the off position. These were taken of of used stoves, but we cannot guarantee they will work without being cleaned up and worked over. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980
-
Leather Pump Cup - 10 PACK - S81
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves. Has a 7/8 inch diameter and is made of oiled leather.
-
-
Valve Assembly Small Stem - E1292
Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.
-
-
Filler Cap Dark Green Used - E1431
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with one (photo is for illustration purpose only)
Comes with a new gasket for you to install.
-
Stove Tank Red Used - ST2
Used tank for the model 413C - 413F, and 442 & 442A stove. This is the late production, red colored.