520

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a screw in the center then these gaskets will work. 

Red 3 piece filler cap show for demonstration purposes only.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. Comes with the new O ring. If your part diagram calls for the 242B5381 or a 621-5361 check valve then this would be the correct part. The latest part number for this is 2006381ZCL.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made of oiled leather.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove. 

Has gone in the past by part numbers 220C1401, and now 425A1405

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Gas tip for the model 520 Military Stove and the 530 stove.

For the model 520 pocket stove. New generator includes new gas tip and tip cleaning wire.

Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove.  It has a vertical sprocket-type valve wheel.  The generator on that stove seems to be unique in that it's a bit shorter than the later version.

Pump Clip

This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear.

Comes with a new gasket.

This is a reproduction aluminum funnel and chain for the Coleman military lantern and 530 stove.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

This is a reproduction flame diffuser plate for the 520 and 530 stoves. These are very nice plates. Professionally cut. 4 inch diameter.

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket NOT installed.

New old stock valve assembly for the model 520 and 523 stoves, comes with pre-heater cup and vaporizer.

This is the small part that attaches to the filler cap screw so you can hook the chain to it.

Wrench for the military model 520 stove. New old stock. These are not stamped US and they do not have the little clip on the opposite side.

This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. 

Comes with a new gasket - not installed

This is the gasket for the one piece filler caps. If your filler cap looks like the one pictured then this gasket is the correct one. 

If your filler cap has a screw in the center of it then this gasket will not work. 

The red filler cap is shown for illustration purposes only and is not included.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Pot support leg for the model 520 stove. New old stock but they show signs of rust.

Tip cleaner needle for inside the vaporizer on a model 520 stove. NOS - will show some surface rust here and there from sitting on a shelf for many years.

Parts tube for the M1941, M1942, 520 and 523 military stoves. 

Each contains a new vaporizer, gas tip, large packing, and 3 screens.

Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247 and similar lanterns. Also fits the 520/M1941 stove.

Burner for the 520 military stove. New old stock but will show signs of a little rust.

Clip to hold a spare generator used on the early 520 military stove. Comes with the new generator.

Stainless steel diffuser plate for the model 530 stove. 4 inch diameter. Professionally cut.

Parts tube for 520 and 523 military stoves. Contains a new vaporizer, gas tip, large packing, and 3 screens. The outer tube is rusty but the parts inside are fine.

Military wrench for the model 520 stove. Stamped US. These have some corrosion on them that you can see in the picture.

Parts tube for 520 and 523 military stoves. Contains a new vaporizer, gas tip, large packing, and 3 screens. The outer tube has a minor rust spot or two. The parts inside are fine.

This is a used one piece filler cap. Paint is chipped or missing, wear and shade of the filler caps varies. 

Comes with a new gasket - not installed

This is a used one piece filler cap. Each one will vary in wear.

Comes with a new gasket - not installed

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.

NOS plastic back up plates for pump assembly