M1942

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Cap Gasket for M1942 & M1950 stoves.

Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.

This is a reproduction aluminum funnel and chain for the Coleman military lantern and 530 stove.

Pump check valve pip for M1942 stove.

Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

Decal for the M1942 stove. Decal is peel and stick.

Parts tube for the M1941, M1942, 520 and 523 military stoves. Each contains a new vaporizer, gas tip, large packing, and 3 screens. LINK for great info on these and what they fit.

For the model 520 stove. New generator includes new gas tip and tip cleaning wire. LINK for great info on these and what they fit.

Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove.  It has a vertical sprocket-type valve wheel.  The generator on that stove seems to be unique in that it's a bit shorter than the later version.

This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.

This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Valve stem nut for many Coleman lanterns.

This is the spring used in the non return valve located in the bottom of the M1942 pump. Reproduction part.

M-1942 Mod Tip Cleaner Graphite packing for all companies who manufactured the stove.  

Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.

Chain for military lanterns and stoves. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.

Decal for the Coleman made M1942 MOD military stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway made M1942 MOD military stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Aladdin made M1942 MOD military stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Burner bowl for the M1942 military stove.

NOS filler cap and chain for the military lantern. Will also fit any Coleman lantern or stove that used the standard size filler cap.

Used valve stem nut for many Coleman lanterns.