M1950

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point. The inside diameter of the 427 pump tube measures .68 inches or 11/16".

This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.

Cap Gasket for M1942 & M1950 stoves.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.

New rubber pip for the re-buildable NRV type check valve used on the 242, 242A, and the M1950 stove.

Fuel tube gasket for the model M1950 military stove.

This is the small part that attaches to the filler cap screw so you can hook the chain to it.

This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.

New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.

These will not fit the 530 stoves without modifications that use a M1950 generator and keeping the 530 needle.

Copper vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

Reproduction needle for the 530 vaporizer. Will also work on the M1950 vaporizer.

For the model M1950 or 536 stove.

Chain for military lanterns and stoves. These are 8" long which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.

Leg for the M1950 military stove.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Reproduction wrench for the model 536 or M1950 stove. 

Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1942, M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically, this is used on the old 327 QuickLites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

These are original style waterslide decals. Design taken from a M1950 stove built in 1963 by Rogers, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

This is a reproduction knob for the Coleman made M1950 stove. The color of these match the original Coleman made color. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.

These are original style vinyl decals. Design taken from a M1950 stove built in 1974, but may fit other years. 

This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1966, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

This is a reproduction knob for the Rogers made M1950 stove. The color of these match the original Rogers darker color. We have found the earlier stoves (made around 1953) were darker than the newer ones (made around 1963). The last photo shows the difference in color between the two. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.

Design taken from a M1950 stove built in 1987 by SMP, but may fit other years. 

This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1951 by Coleman with a silver label, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

Design taken from a M1950 stove built in 1987 by SMP, but may fit other years. 

This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

This is a reproduction knob for the Rogers made M1950 stove. The color of these match the original Rogers lighter color. We have found the earlier stoves (made around 1953) were darker than the newer ones (made around 1963). The last photo shows the difference in color between the two. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.

These are original style waterslide decals. Design taken from a M1950 stove built in 1951& 52 by Rogers, with a gold label, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1963 by Rogers with a gold label, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1951& 52 by Rogers, with a silver label, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

Design taken from a M1950 stove built in 1974, but may fit other years. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1951 by Coleman with a gold label, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1963 by Rogers with a Silver label, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

These are original style waterslide decals. Design taken from a M1950 stove built in 1972, but may fit other years.

Click on the "Description" under the photo to see the waterslide installation instructions.

Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1942, M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

These ones do not come in the cardboard wrapping and may be unfolded (see photos).