M1942

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Cap Gasket for M1942 & M1950 stoves.

Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.

Pump check valve pip for M1942 stove.

Copper vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

These are NOS tubes, probably from the WWII era.  These fit the model M1941 which is also called the 520 military stove. Also fits the  523, which is a two burner stove but you would need 2 tubes for it.

Tubes are very old - show some surface rust on the outside, but the contents are in great shape.

This is a soft parts rebuild kit for the M1942 stove. Includes the cap gasket, check valve dot, and pump leather.

This is the spring used in the non return valve located in the bottom of the M1942 pump. Reproduction part.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Reproduction knob for the M1942 stove tip cleaner. Identical to the original.

M-1942 Mod Tip Cleaner Graphite packing for all companies who manufactured the stove.  

Reproduction valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 & 530 stoves and may fit others.

Decal for the Aladdin made M1942 MOD military stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Preway made M1942 MOD military stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.

Decal for the Coleman made M1942 MOD military stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

When you buy this decal with free shipping, we’ll send it in a stamped envelope via USPS mail. It will ship within 1 business day and arrive within standard USPS delivery times for a regular letter.

Reproduction Hex Pip holder. This connects the spring and the pip used in the non return valve located in the bottom of the pump. 

Gas tip for the model M1942 stove. LINK for great info on these and what they fit.

Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1942, M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

Used valve stem nut for many Coleman lanterns.