Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Replacement Check Valve and Air Stem This is the standard replacement part for most Coleman lanterns and stoves manufactured after 1946, as well as select earlier models. It features the updated design with a smaller air stem head; the included new stem is designed to replace your existing one entirely.
Fits models requiring part numbers 242B5381, 621-5361, or 2006381ZCL.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.
Also known as part number 425A1405.
Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.
Also known as part number 3000005094.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This generator is designed for larger two-burner and three-burner stove models.
Fits Coleman Stove Models:
413 Series: 413E, 413F, and 413G.
426 Series: 426B, 426C, and 426D.
Other Models: 442, 442A, and 443.
Also known as part number: 3000005106.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.
Comes with a new gasket that you will have to install.
This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.
Fits models requiring part numbers 200-6381, 400-6381, 242B5381, 242B538 or 621-5361.
10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Original NOS Coleman pump cup that fits most lanterns and stoves, they have been sitting around for many years and may not have their perfect shape and some are almost flat.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is a used pump square nut.
Comes with one square nut ONLY.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
Original NOS Coleman pump cup that fits most lanterns and stoves.
They are flat and have lost most of their shape from sitting around over the years
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
This is a used 3-piece filler cap. These caps show varying levels of wear, with chipped or missing paint. The one you receive may look like any of the examples shown in the photos. We select the best-condition pieces available first.
We are showing three different caps for demonstration purposes only to illustrate possible condition. This listing is for one cap.
It comes with or without the side vent hole (whichever is in stock when we pick your order). A new gasket is included for you to install if needed.
NOS Burner Bowl (Master). May be tarnished from sitting on a shelf over the years.
This part no longer being made by Coleman.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is for one used 3 piece filler cap. They are in various stages of wear. Finish may be chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.
Also has been reported that it works on "some" AGM check valves.
How to Use Your Check Valve Removal Tool
Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.
Follow these steps carefully to remove and reinstall the check valve safely:
To reinstall the check valve: Simply reverse the steps above.
If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!
For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com
Used Pump Assembly Spring
Spring ONLY
Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% Teflon - the original was graphite. These seal well and can be reused.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P4 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.
These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
NOS Valve Body - This is a NOS Valve body that takes the small 3/16" stem only, for early Coleman 425 series camp stoves (pre-425F models). It pairs with part 412-2531 to create a complete valve assembly.
Important sizing check: This small-stem version takes a 3/16" valve stem. Coleman’s later 425 models (around 1995+, often unmarked 425H) use a larger 1/4" stem—this part will not fit those. Measure your stem diameter before ordering to avoid frustration.
Used steel filler cap for Coleman lanterns. These are original caps in average used condition with varying amounts of rust (photo shows a typical example). These are solid, but ugly, good for projects where you are going to repaint things. Includes a new gasket that you will need to install yourself.
Fits most Coleman lantern models.
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
This is a NOS old style Valve & Generator with the thicker generator tube. Fits 413E through 413G and 426D, 442, and 442A stoves. Does not fit the 413H.
This decal is for the Sears Model 476.72302 stove. It calls out the 7469 generator which is used on models 476.72302, 476.72303, 476.74970, and 476.74980. We placed this on a black background so you can read the text. Very nice decal with proper dimensions. Some Sears stoves appear to have a green or yellow tint on the original but they originally came clear with white backgrounds like this reproduction decal - age has caused the different color.
When you buy this decal with free shipping, we’ll send it in a stamped envelope via USPS mail. It will ship within 1 business day and arrive within standard USPS delivery times for a regular letter.
Used valve stem for the 413E, 413F, 413G, 413H, 424, 425F, 425G, 426D, 442, 442A stoves. Also fits Sears stove models 476.72302, 476.72303, 47.74970 & 476.74980.
You will need a P01 graphite packing for these which is HERE. Measurements: just over 1-3/4" long and 1/4" diameter.
Please read this if you have a 425F: This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem and make sure it is 1/4".
