132A
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a screw in the center then these gaskets will work.
Red 3 piece filler cap show for demonstration purposes only.
-
Generator Lantern - C02
New generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as the old part number T44. Same as new part number 3000005090.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
New Filler Cap Brass - C04
New brass one piece filler cap. Fits most all lanterns and stoves other than the model 242 lantern and 500 stove.
Also known as part number 425A1405.
-
Used Generator Nut - S26
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
-
Generator Nut - S176
Generator nut. Fits many models of lanterns which take the 220E5891 generator: 220s, 228's, 275. Also fits many other models. Find your parts diagram HERE and verify the generator nut is listed as 605-210.
-
-
Filler Cap Tire Valve Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
-
Lamp Globe Reproduction - G08
Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.
-
Burner Tube Brass 2 7/8 - E1264
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
-
Lamp Hanger New - R502
New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.
-
Needle Assembly Used - S08
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
-
-
Globe Holder Clamps Reproduction - R607
Reproduction globe holder set. Used on all later Coleman lamps that used a globe. We have found these clamps to not have the bend quite like the originals - you most likely will need to bend it slightly to match the original. We bent this set by hand without any special tools. We will make the correction on the next batch we get.
-
Lamp Globe Holder - R503
This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.
-
Shade Holder Rod With Nut - S128
Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.
-
Burner Tube Short - S132
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
-
Filler Cap Green Used - E1248
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.
-
Used Generator Spring - S29
Used generator spring for 220, 228, 275 lanterns. Also fits some Sears models.
Will show signs of use but will be in good shape.
-
Burner Tube 2 1/2 Inch - E1471
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
-
Filler Cap Dark Gray Used - E1307
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Dark gray in color like the new production Duel Fuel models.
Comes with a new gasket for you to install.
-
Filler Cap 3 Piece Red Used - E1372
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
-
Filler Cap Nickel New - R314
This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
-
Filler Cap Brass New - R319
This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
-
-
-
-
Filler Cap Light Gray Used - E1208
Used filler cap that fits most Coleman lanterns and stoves. Light gray in color like the early production Duel Fuel models. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket that you will have to install.
-
-
Air Intake Tube Brass - E1137
Reproduction air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.
-
Air Stem Reproduction - S126
Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.
-
Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a screw in the center then these gaskets will work. Red 3 piece filler cap show for demonstration purposes only.
-
Burner Tube Brass 2 3/4 - E1129
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
-
Burner Tube Steel Old Style - E1101
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
-
Used Generator Body - E1478
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
-
Large Valve Stem Packing - 10 PACK - P01
This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
-
Filler Cap Dark Green Used - E1431
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with one (photo is for illustration purpose only)
Comes with a new gasket for you to install.
-
Filler Cap Brass Outer Cap Used - E1179
This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
-
Mixing Chamber Used with Vent Rod - E1001
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
-
Lamp Shade - L15
Only 1 left in stockThese shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.
This product is not included in the OCP free shipping program. +
-
Lamp Shade Red Floral - L14
Only 2 left in stockThese shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.
This product is not included in the OCP free shipping program.
-
Lamp Shade White Floral - L12
Only 2 left in stockThese shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.
This product is not included in the OCP free shipping program.
-
Lamp Shade Blue Floral - L11
Only 2 left in stockThese shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.
This product is not included in the OCP free shipping program.
-
Lamp Shade Green Floral - L10
Only 2 left in stockThese shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.
This product is not included in the OCP free shipping program.