133

Products: 141 of 41
Show: 50
  • Filler Cap Gasket for 3 Piece Cap - S41
    • Free Shipping

    Filler Cap Gasket for 3 Piece Cap - S41

    This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

    If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

    Red 3 piece filler cap shown for demonstration purposes only.

    Score: 5.00 (votes: 2)
    Reviews: 2
    |
    2
    • $1.25
  • Generator Lantern - C02

    New generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as the old part number T44. Same as new part number 3000005090.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $17.75
  • Large Valve Stem Packing - P01

    Typically used to stop a fuel leak from the valve stem on older appliances.

    This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

    If you need to check your model, please see the PARTS DIAGRAM PAGE

    425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

    Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

    Made of 100% graphite.

    Not rated yet
    • $3.55
  • Used Generator Nut - S26

    Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

    Not rated yet
    • $2.00
  • Generator Nut - S176

    Generator nut. Fits many models of lanterns which take the 220E5891 generator: 220s, 228's, 275. Also fits many other models. Find your parts diagram HERE and verify the generator nut is listed as 605-210. 

    Not rated yet
    • $5.85
  • Lamp Globe Reproduction - G08

    Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $29.00
  • Burner Tube Brass 2 7/8 - E1264

    Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

    Not rated yet
    • $4.35
  • Needle Assembly Used - S08

    Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

    Not rated yet
    • $4.50
  • Gas Tip Used - GT1

    Used Gas tip.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $2.15
  • Globe Holder Clamps Reproduction - R608

    Reproduction globe holder set. Used on all later Coleman lamps that used a globe. We have found these clamps to not have the bend quite like the originals - you most likely will need to bend it slightly to match the original. We bent this set by hand without any special tools. We will make the correction on the next batch we get.

    Not rated yet
    • $10.00
  • Shade Holder Rod With Nut - S128

    Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.

    Not rated yet
    • $8.95
  • Lamp Globe Holder - R502

    This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.

    Not rated yet
    • $15.55
  • Used Generator Spring - S29

    Used generator spring for 220, 228, 275 lanterns. Also fits some Sears models.

    Will show signs of use but will be in good shape.

    Not rated yet
    • $5.00
  • Burner Tube Short - S132

    Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

    Not rated yet
    • $7.00
  • Burner Tube 2 1/2 Inch - E1471

    Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

    Not rated yet
    • $5.40
  • Filler Cap Nickel New - R303

    This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

    Not rated yet
    • $19.40
  • Decal - Fits 143 Lamp - D49
    • Free Shipping

    Decal - Fits 143 Lamp - D49

    143 Lamp Decal

    Not rated yet
    • $6.35
  • Filler Cap Brass New - R317

    This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

    Not rated yet
    • $19.00
  • Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41
    • Free Shipping

    Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41

    This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

    Not rated yet
    • $11.25
  • Generator Lantern, Reproduction - R204

    Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.

    Not rated yet
    • $14.60
  • Fuel Air Tube Reproduction - R406

    Reproduction fuel and air tube for lamps.

    Not rated yet
    • $17.35
  • Aluminum Funnel Small - R614

    This is a new aluminum filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243 and similar lanterns or the 500 stove.

    Not rated yet
    • $5.50
  • Pump Assembly, 220C Thick Steel Cap, Used - E1296

    This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.

    Not rated yet
    • $22.00
  • Pump Assembly, 220B Thin Brass Cap, Used - E1420

    This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.

    Not rated yet
    • $22.00
  • Large Valve Stem Packing - 10 PACK - P01

    This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

    This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

    If you need to check your model, please see the PARTS DIAGRAM PAGE

    425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

    Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

    Made of 100% graphite.

    Not rated yet
    • $31.95
  • Eccentric Block Used - S101

    Used Eccentric Block 


    Not rated yet
    • $5.00
  • T44 Generator - E1558

    T44 generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Same generator as part number 220E5891.

    Comes in original packaging.

    Not rated yet
    • $23.00
  • Air Intake Tube Brass - E1137

    Reproduction air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.

    Not rated yet
    • $10.85
  • Used Generator Body - E1478

    These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.

    Not rated yet
    • $1.00
  • Air Stem Reproduction - S126

    Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.

    Not rated yet
    • $13.00
  • Burner Tube Steel Old Style - E1101

    Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

    Not rated yet
    • $4.35
  • Burner Tube Brass 2 3/4 - E1129

    Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

    Not rated yet
    • $4.35
  • Pump Assembly, 220B Thick Brass Cap, Used - E1390

    This is a used pump assembly for the model 220b.  It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick. Has a nickel plated brass cap.

    Not rated yet
    • $22.00
  • Nut - E1151

    Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.

    Not rated yet
    • $1.35
  • Pump Brass Cap NOS - E1123

    New old stock long pump for the model 220B and 220C lantern. These have a brass cap that connects the pump to the lantern. They have new pump leather on them. Probably made in the 1930's or early 40's.

    Not rated yet
    • $20.60
  • Mixing Chamber Used with Vent Rod - E1001

    Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

    Not rated yet
    • $6.75
  • Filler Cap Brass Outer Cap Used - E1179
    • 67% less

    Filler Cap Brass Outer Cap Used - E1179

    This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

    Not rated yet
    • $2.00
  • Pump Assembly 220B Canadian NOS - E1149

    This is a NOS pump assembly for the Canadian model 220B. It would also be correct for the 427 and 228B Canadian lanterns. The Canadian pump differs from the US in having a splined screw on cap rather than a checkered style.

    Not rated yet
    • $30.00
  • Lamp Shade White Floral - L12

    These shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.

    This product is not included in the OCP free shipping program.


    Not rated yet
    • $83.50
    Only 1 left in stock
  • Lamp Shade Blue Floral - L11

    These shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.

    This product is not included in the OCP free shipping program.


    Not rated yet
    • $83.50
    Only 1 left in stock
  • Lamp Shade Green Floral - L10

    These shades are hand made here in the USA. These require a large box size to ship and is the reason for the $65 shipping fee that you will see in checkout. International buyers may see a refund or a request for more shipping after the purchase depending on your location.

    This product is not included in the OCP free shipping program.


    Not rated yet
    • $83.50
    Only 1 left in stock