143

Products: 141 of 41
Show: 50
  • Mixing Chamber Used - E29

    Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

    Not rated yet
    • $9.75
  • Eccentric Block - S137

    Eccentric Block

    Not rated yet
    • $7.60
  • Filler Cap Gasket for 3 Piece Cap - S41
    • Free Shipping

    Filler Cap Gasket for 3 Piece Cap - S41

    This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

    If your filler cap is a standard size and has a screw in the center then these gaskets will work. 

    Red 3 piece filler cap show for demonstration purposes only.

    Score: 5.00 (votes: 2)
    Reviews: 2
    |
    2
    • $1.25
  • Gas Tip Used - GT1

    Used Gas tip.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $2.15
  • Fuel Air Tube Reproduction - R406

    Reproduction fuel and air tube for lamps.

    Not rated yet
    • $17.35
  • Pump Assembly 220B Brass Thin Used - E24
    • New!

    Pump Assembly 220B Brass Thin Used - E24

    This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. I have pictured both styles. They are interchangeable. You are purchasing the style one labeled "Thin" with the thinner knurled portion. Make sure you get the one you want.

    Not rated yet
    • $24.00
  • Burner Tube Brass 2 7/8 - E36

    Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

    Not rated yet
    • $4.35
  • Large Valve Stem Packing - P1

    Typically used to stop a fuel leak from the valve stem on older appliances.

    This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

    If you need to check your model, please see the PARTS DIAGRAM PAGE

    425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

    Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

    Made of 100% graphite.

    Not rated yet
    • $3.55
  • Filler Cap Brass New - R319

    This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

    Not rated yet
    • $19.00
  • Generator Nut - S176

    Generator nut.

    Not rated yet
    • $5.85
  • Decal - Fits 143 Lamp - D49
    • Free Shipping

    Decal - Fits 143 Lamp - D49

    143 Lamp Decal

    Not rated yet
    • $6.35
  • Filler Cap Nickel New - R314

    This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

    Not rated yet
    • $20.60
  • Pump Assembly 220B Thick Used - E312
    • New!

    Pump Assembly 220B Thick Used - E312

    This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. 

    Not rated yet
    • $22.00
  • Pump Assembly 220C Steel Cap Used - E848

    This is a used pump assembly for the model 220C. It has a steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape.

    Not rated yet
    • $19.55
  • Burner Tube Nickel Plated

    This is a nickel plated brass burner tube. Not polished. More of a utilitarian type finish. For most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

    Not rated yet
    • $7.60
  • Lamp Globe Holder - R503

    This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.

    Not rated yet
    • $15.55
  • Air Intake Tube Brass - E178

    Reproduction air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.

    Not rated yet
    • $10.85
  • Lamp Globe Reproduction - G8

    Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.

    Score: 5.00 (votes: 1)
    Reviews: 1
    |
    1
    • $29.00
  • Used Generator Nut - S26

    Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

    Not rated yet
    • $2.00
  • Lamp Finial and Nut Reproduction - R317

    Reproduction lamp finial and nut for later Coleman lamps. Made of brass. Identical to the original.

    Not rated yet
    • $19.55
  • Iron Pump Reproduction - R311

    Reproduction small pump for the Coleman irons. Will also work on any Coleman lamp or lantern.

    Not rated yet
    • $23.10
  • Air Stem - E170

    New Old Stock Air stem / thumb screw for filler plugs used on the old Quicklite lanterns and lamps. These are all brass. None have any nickle plating on them.

    Not rated yet
    • $15.20
  • Mixing Chamber Aluminum - E108

    Aluminum mixing chamber for most double mantle lanterns and lamps. Coleman experimented with aluminum for a few parts back in the old days. I believe it was discovered that aluminum could not hold up to the heat. Probably more of a display piece than for using.

    Not rated yet
    • $10.85
  • Burner Tube Short - S132

    Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

    Not rated yet
    • $7.00
  • Shade Holder Rod With Nut - S128

    Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.

    Not rated yet
    • $8.95
  • Burner Tube 2 1/2 Inch - E32

    Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
    Not rated yet
    • $5.40
  • Air Intake Tube Steel - E453

    Air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.

    Not rated yet
    • $11.95
  • Burner Tube Steel Old Style - E114

    Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

    Not rated yet
    • $4.35
  • Air Stem Reproduction - S126

    Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.

    Not rated yet
    • $13.00
  • Pump Assembly 220B Canadian Used - E386
    • New!

    Pump Assembly 220B Canadian Used - E386

    This is a used pump assembly for the Canadian model 220B. It would also be correct for the 427 and 228B Canadian lanterns. It has been cleaned and has a new pump leather installed. The Canadian pump differs from the US in having a splined screw on cap rather than a checkered style.

    Not rated yet
    • $26.00
  • Globe Holder Clamps Reproduction - R607

    Reproduction globe holder set. Used on all later Coleman lamps that used a globe. We have found these clamps to not have the bend quite like the originals - you most likely will need to bend it slightly to match the original. We bent this set by hand without any special tools. We will make the correction on the next batch we get.

    Not rated yet
    • $10.00
  • Burner Tube Brass 2 3/4 - E448

    Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

    Not rated yet
    • $4.35
  • Filler Cap Brass Outer Cap Used - E71

    This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
    Not rated yet
    • $10.85
  • Nut - E419

    Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.

    Not rated yet
    • $1.35
  • Eccentric Block Used - S101

    Used Eccentric Block 


    Not rated yet
    • $5.00
  • Needle Assembly Used - S8

    Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

    Not rated yet
    • $4.50
  • Pump Assembly 220B Brass Used - E452

    This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. 

    Not rated yet
    • $23.85
  • Used Generator Spring - S29

    Used generator spring for 220, 228, 275 lanterns. Also fits some Sears models.

    Will show signs of use but will be in good shape.

    Not rated yet
    • $7.05
  • Nut - E271

    Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.

    Not rated yet
    • $2.45
  • Mixing Chamber Used with Vent Rod - E105

    Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

    Not rated yet
    • $9.75
  • Used Generator Body - E38

    These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.

    Not rated yet
    • $4.00