152A

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

New Coleman made generator for 220, 228, 275, and similar Sears lanterns. The new generator includes new gas tip, spring, and tip cleaning wire.

Will fit Coleman Lanterns: 220 B thru 220 J, 228 B thru J, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070

This is the same generator as the old part number T44 and same as new part number 3000005090. 

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.

Reproduction shade holder for the old CQ style lamps.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.

Reproduction globe holder set. Used on all later Coleman lamps that used a globe. We have found these clamps to not have the bend quite like the originals - you most likely will need to bend it slightly to match the original. We bent this set by hand without any special tools. We will make the correction on the next batch we get.

Used Gas tip.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket for you to install.

Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.

Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.

This is a10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Reproduction fuel and air tube for lamps.

This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar.

Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.

Reproduction air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.

Newer style mixing chamber for the model 220/228 lanterns. 

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

This is for one used 3 piece blue filler cap. Shade and wear may vary.

Comes with a new gasket that you will have to install.

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.