This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The green filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is the small tube that goes inside of the 200A, 220/228 and 288 size generators. May fit others too.
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the irons, model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Replacement Generator New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part numbers T66, 200A2891, and 3000005089.
Fits Coleman Lantern Models: 200, 200A, 202, 242, 243, and similar Sears lantern models.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal the typical Coleman lantern cap.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.
Also known as part number 425A1405.
This replacement screen will fit the burner caps used on 200, 200A, 201, 242, and 243 lanterns.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.
Also known as part number 3000005094.
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
Customers have reported that these work well on Powermate Heaters.
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.
Need more information on the valve core? Click HERE.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Burner screen for double mantle lanterns and lamps. Fits 220s, 228s, 117, 129, 129G and CQ lamps. Fits most double mantle lanterns and lamps with small burner caps.
Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point. The inside diameter of the 427 pump tube measures .68 inches or 11/16".
New Coleman-manufactured burner cap designed for lantern models 200, 200A, 202, 243, 242, and 247. This part is also compatible with several lamp models and Sears lanterns.
Also known as part number 2423231.
New Coleman-manufactured pump cup designed for all lanterns that originally utilized the rubber-style cup.
Also known as part number 639-1091.
New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.
Also known as part number 242J5201.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. Also fits the 530 Pocket Stove. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
New Coleman-manufactured feed tube assembly. This component comes complete with a new Schrader valve and O-ring.
Fits Coleman Lantern Models: All 282, 285, 286, and 288 models.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
New 2 oz. alcohol bottle specifically for kerosene lanterns. This is the standard tool used to fill the pre-heater cup with alcohol prior to lighting the lantern.
Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.
O-Ring sizes are #6, #7, and #9, made of Flourosilicone.
We know it does work on these models: 533 (need 2), 442
Does not work on the 400B, 508B, 533A, 3024
New Coleman-manufactured 2-pack of ball nuts. This is the common size used on the majority of Coleman lanterns.
Also known as part number 3000005384.
Used generator nut for many Coleman models. These are in fine shape, just dirty.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
This also works well as part number 335-0604 used on the burner frame/tube for the 335 lantern.
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 234, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.
Also known as part number 242-353.
Used, round headed valve wheel screw. Will be in good condition. These fit many models. Over the years, they changed the types of screws to hold on valve wheels. Please compare how this looks to yours if ordering. These will not fit the 236 or 237.
Filler plug gasket for the model CQ lamps, 327 Quick-lite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
New rubber pip for the re-buildable NRV type check valve used on the 242, 242A, and the M1950 stove.
Fits Coleman Lantern Models: All 290 and 295 versions.
New steel fuel pick-up tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Also known as part number 200-1481
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
This 10 pack of gaskets are for many Coleman lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center like the example that is shown, then these gaskets will work.
New filler cap screw for the small cap on the 242, 243, 246, 247 & 249 lanterns and 500 stove size filler caps.
Reproduction needle assembly for the 200A2891 T66 generator used on lantern and lamp models 121, 200, 200A, 202, 242, 242B, 242C, 243, 476.72211 & 476.74550.
