Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point. The inside diameter of the 427 pump tube measures .68 inches or 11/16".
They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
Filler cap gasket for the Prentiss Waber lantern. OD just under 1", ID 5/8".
O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.
This is a large filler cap gasket for the Handy Gas Plants AND Coleman Heaters (Models 2, 4, 5 & 7). It also works for the Tilley R1 heater.
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.
Decal for the Thermos lantern. It is approximately 2 1/2 inches long and is 1 1/4 inches high at the widest point. The background silver is too sparkly on these. Reduced price to sell.
Pointed Bottom Sears Lantern Replacement Decal
Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.
Sears Lantern Logo Replacement decal featuring the rectangular design, specifically for later Sears lantern models.
Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.
Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly
Ted Williams replacement decal for Sears Ted Williams lanterns
Reproduction inverted generator for the AGM Kamplite inverted lanterns. Fits models IL1, IL11, and Thermos models 8319, 8321.
Very old NOS Akron generator.
These are compatible with Lantern Models 131, 132, 132AG, 132G, 134G, 301G, and Lamp Models 125 Utility, 140-BG, 140-B, 155, as well as Art Deco Models 486B7257 and 486C7258. May also be compatible with Montgomery Ward Lanterns.
The generator body measures 4 3/16 inches in length. Supplied without packaging.
This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.
Decal for the Thermos "Holiday" lantern.
One mantle per pack. Used on 500-550 candlepower lanterns. Made in USA
AGM lantern screen retainer. Has an approximate diameter of 7/8 of an inch. This holds in the burner screen to the burner frame. Fits single mantle models like the 3016, may fit others. The 200A burner screen HERE will fit in these burner frames if you trim it a little with scissors.
Decal for the AGM model 3016 Lantern. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
This is an AGM made generator that will fit many AGM models. Does not come in original box. Box is just to show application. Fits the below models and probably many others. Tube width is 1/4". Overall length is 3-11/16" long.
AGM generator. Generator body including gas tip measures 3 3/16 inches long.
Fits models 2572, 3016, RL-2, RL-3
Same as part number 458-073.
Packaging may vary.
Decal for Montgomery Ward Hawthorne lantern.
NOS Leather Pump Cup. Has holes punched in it on each side of the center hole. Not sure what these were made for or what the white powder substance is on the outside of the leather.
This is the common sized Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter.
Preway Stove Generator Gas Tip for 401, 402, 404, 409, 4521, 4522, 4521A, 4522A, 4821, 4822
Thermos tip cleaner. Measures 2 5/8 inches long.
This is an original filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
AGM generator used on various models. Will fit AGM model 3606 and other for single mantle AGM fixtures. Generator body is about 4 inches long. Gas tip is unmarked.
This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:
Burner ring for Thermos stoves. May show signs of light rust.
Generator for AGM lanterns. Measures 3 1/8 inches long. Fits the AGM model 3025 lantern, may fit others.
Used Sears valve assembly - comes with a new graphite packing for you to install if needed. Has the shorter fuel tube to accommodate the shallower Sears fuel tank.
Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.
Lead gasket for the NRV check valves for Primus, Optimus, Radius, and Svea Stoves/Lanterns. May fit others.
Diameter is approximately 1/2"
Gasket ONLY.
Fuel tube. Measures 2 1/2 inches long.
Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).
Fuel tube. Measures 3 1/8 inches long.
Burner cap with 5 holes for thermos lanterns.
Thermos generator for models 8489, 8490, 8491 stoves. New generator includes new gas tip, spring, and tip cleaning wire.
Fuel tube and screen for Thermos stoves. It is 3 inches long.
Generator for Akron Iron model 2. Runs on gasoline.
Burner cap for the European style lanterns such as the Petromax 500
This is a used collar for a model 476.74070 Sears lantern. Wear will vary.
Burner cap with 3 holes for Thermos lanterns.
Term-Sport Alcohol Stove Tank Decal. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.
Decal for the Preway Model P4521 stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
