Stove Parts

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The green filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. Also known as part number 3000005094.

This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.

This fits many applications for propane appliances. 

We have been told it works well on Powermate heaters, 45000, 17000 and 15000 btu units.

O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400, 5400A.

Two required for the model 550 stove.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

This is a soft parts rebuild kit for the M1950 stove.
Includes a cap gasket, check valve dot, fuel tube gasket and a new pump leather.
Should cure most issues.

This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.

Also known as part number 639-1091

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

Also known as part number 242J5201.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Cap Gasket for M1942 & M1950 stoves.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

This is the gasket only from the 5423A5611 small parts kit.

OD 1/2", ID 3/16", Thickness is just under 1/16"

Was commonly used on the model 5413, 5413A, 5423, 5430B, 5433, 5430B, 5430C, 5435C, 5435D and similar propane stoves.

Pump Clip

Reproduction wrench for the 530 pocket stove.

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.

This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5400A, 5410, 5428 but may fit other also.

This does not work on the 5430-700, 5430A700 or the 5430B700.

Coleman Decal For Pre-1963 Camp stoves. These are large decals and are for suitcase type stoves. Small stoves like the model 502 would use a lantern decal D11. This decal measures approximately 3 1/4 inches wide and is 1 1/8 inches high.

When you buy this decal with free shipping, we’ll send it in a stamped envelope via USPS mail. It will ship within 1 business day and arrive within standard USPS delivery times for a regular letter.

Pump check valve pip for M1942 stove.

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

Fuel tube gasket for the model M1950 military stove.

Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091

This is a reproduction flame diffuser plate for the 520 and 530 stoves. These are very nice plates. Professionally cut. 4 inch diameter.

Coleman Decal for Stoves Made After 1964 With White Border. These are large decals and are for suitcase type stoves. Small stoves like the model 502 would use a lantern decal D11. This decal measures approximately 3 1/4 inches long and is 1 1/4 inches high. Also would work well for car window, notebooks, etc. Has been reported to fit the 5280 model cooler perfectly also.

When you buy this decal with free shipping, we’ll send it in a stamped envelope via USPS mail. It will ship within 1 business day and arrive within standard USPS delivery times for a regular letter.

4 Screws W/Washer Stainless For 530. These also work for the 500 and 500A stoves.

Also known as part number 1012B1004 & 1012B1004

Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.

These will not fit the 530 stoves without modifications that use a M1950 generator and keeping the 530 needle.

Copper vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.

This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.

Coleman Logo for Camp stoves Made After 1963. These are large decals and are for suitcase type stoves. Small stoves like the model 502 would use a lantern decal D11. Measures approximately 3 " across the top and is 1 1/8 inches high.

When you buy this decal with free shipping, we’ll send it in a stamped envelope via USPS mail. It will ship within 1 business day and arrive within standard USPS delivery times for a regular letter.

Reproduction needle for the 530 vaporizer. Will also work on the M1950 vaporizer.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.

New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉. 

Sheets are 4-3/4" in diameter and 1/32" thick.

NOS lighting stem.

Master Burner Bowl, Rings and Screw 413E/413F/413G/424/426B/426D/426G/442/442A/443 Instant Light, 2 & 3 Burner Stoves

Valve assembly for the 400B, 3024, 442 and 440 single burner stoves.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

These are NOS tubes, probably from the WWII era.  These fit the model M1941 which is also called the 520 military stove. Also fits the  523, which is a two burner stove but you would need 2 tubes for it.

Tubes are very old - show some surface rust on the outside, but the contents are in great shape.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Regulator Assembly - screw on. If you want the clip-on regulator then it would be 9942-5251. Will fit on RoadTrip Grill Models: 9949, 9949A, 9941, and may fit others

Also known as part number 5010000743.

This is a soft parts rebuild kit for the M1942 stove. Includes the cap gasket, check valve dot, and pump leather.