Search

NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.

Spring for the inside of the 236 generator.

These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)

These are NOS Coleman ball nuts

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one is in very good condition.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

Round steel burner cap for most models of double mantle lanterns and lamps.

New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.

Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

Used closed ball nut.

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.

Used direction disk for the later double mantle lanterns such as 220/228, J-K. Will show signs of wear but still be in good condition. 

Used valve stem nut for many Coleman lanterns.

Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

Includes:

• 4 Peerless mantles for your lantern
• 1 Reproduction generator
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.

Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.

This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Longer vent rod for models 220/228B through 220/228E and 235.

This is a used collar for the 220F lantern.

220H collar. This is a used collar and may show signs of wear.

220J Collar. This is a used collar and may show signs of wear.

Shorter vent rod for models 220/228F through 220K

This is a used collar for the 220E lantern. It may show signs of light rust or a little discoloration to the metal. All will vary in wear.

Used collar for the 220K lantern.

Used burner frame that will fit models 220B through early 220F through approximately 1971.

Used washer for the model 220/228H lantern.

This is a used ventilator for the model 220B through 220E lantern. This vent has paint chips (see photos)

This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Used made in Mexico white letter globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Amber globe made in USA. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

New frosted sunrise logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

New half frosted globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

This is a used vent. It will fit models 220B through 220E. 

Has paint chippings and a small bulge towards by the ball nut opening (see photos)

This is a used ventilator for the model 220B through 220E lantern. 

This vent has a few paint chippings. (see photos)

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Used direction disk for the 220/228H lantern. Will show signs of wear but still be in good condition.

This is a used ventilator for the model 220B through 220E lantern. 

Has some paint chips and scratches (see photos)