413D

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. Also known as part number 3000005094.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Used, round headed valve wheel screw.  Will be in good condition. These fit many models. Over the years, they changed the types of screws to hold on valve wheels. Please compare how this looks to yours if ordering. These will not fit the 236 or 237. 

Pump Clip

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980

These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.

NOS lighting stem.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 200-6381 and without the air stem.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Fuel Air Tube for the 413 series and 442 series 2 burner stoves. NOS.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Original NOS Coleman pump cup that fits most lanterns and stoves, they have been sitting around for many years and may not have their perfect shape. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a used steel 3 piece cap.  Comes with a new gasket that you will have to install.

Needle & Holder

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket for you to install if needed.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Finish may be chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Fuel Cap with pressure gauge.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Block and Needle Assembly. Measures approximately 4 1/4 inches long.

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.

This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Reproduction long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Used, round headed valve wheel screw.  Will be in good condition. These fit many models. Over the years, they changed the types of screws to hold on valve wheels. Please compare how this looks to yours if ordering. These will not fit the 236 or 237. 

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.

P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).