220F
- Free USA Shipping
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Peerless Mantles 2C-HG - M01
Most Popular Sized Mantles and are treated with Thorium from the factory. 4 mantles per pack. Use on these models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Will fit all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
- Free USA Shipping
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Generator Tube Packing - P05
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Check Valve With Stem - C001
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
Peerless Mantles 24-A - M04
These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- Free USA Shipping
Decal - Fits 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D11
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
Mantle String Tie #21 4 Pack - M02
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
- Free USA Shipping
Decal - Fits 1965 to 1971 200A, 220 & 228 F Lanterns - D12
White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965 to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G,
Filler Cap, Brass - C004
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
- Free USA Shipping
Decal - Fits 1961 to 1964 200A, 220 & 228 E & F Lanterns - D13
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
Leather Pump Cup Kit - C005
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
- Free USA Shipping
Check Valve O Ring - S20
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Filler Cap Screw 220 Size - S68
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
- Free USA Shipping
220 Burner Screen - S30
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
Mantle String Tie #21 2 pack - M03
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
Graphite Ribbon - P09
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
Pump Cup, Neoprene - C019
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
- Free USA Shipping
Pump Clip, Used - S100
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
Ball Nut, 2 Pack - C011
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.Generator Nut, Used - S105
Used generator nut for many Coleman models. These are in fine shape, just dirty.
Filler Cap Insert, Reproduction - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Ball Nut, Used - S101
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
220/228 Air Tube Screw Phillips - S74
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
This also works well as part number 335-0604 used on the burner frame/tube for the 335 lantern.
Valve Wheel Screw, Used - S103
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Bail Wrap Protector Black - R513
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
- Free USA Shipping
Wrench 220B - R300
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Fuel Tube Spring, Steel - R581
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Pump Assembly Leather Used Square Nut - U810
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Valve Wheel Black Old Style, Used - S113
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Valve Assembly Used - U820
This is a used valve assembly for the models 220/228B through 220/228F and 252/Milspec lanterns. Valve packing has not been changed. If needed, they are HERE.
Filler Cap, Tire Valve, Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Pump Cup & Nut, Neoprene - C008
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091Air Stem, Old Style, Used - S107
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Eccentric Block - E1039
New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.
Black Valve Wheel New Style, Used - S112
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Needle Assembly, Used - S99
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
327 Mica Globe - G09
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
- Free USA Shipping
Filler Cap Gasket for 3 Piece Cap- 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S41
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Tip Cleaner Stem Reproduction - R700
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3