118A

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal the typical Coleman lantern cap.

Used generator nut for many Coleman models. These are in fine shape, just dirty.

This is a quality made reproduction Q99 generator made here in the USA that fits the older Coleman QuickLite style lanterns and lamps. 

Will fit these models: 117, 117A, 118A, 119A, C331, CQ, Model B and Model C Lamps. Poultry, 227, 327 and 427.

Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.

Reproduction lamp globe for the later style Coleman lamps. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Also called the 355 globe.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.

Used Gas tip. Fits 220, 228 model lanterns. Also many lamps that use the same generator 220E5891. 

New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.

New old stock T44G generator. This is the early version of the 220E5891 generator. Instead of a cardboard tube it has a cloth material over the spring. These show a bit of tarnish from being on the shelf for 80 years.

Will fit Coleman Lanterns: 220 B thru 220 K, 228 B thru K, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070

The original box is not included - just showing as an example of the original packaging. 

One generator is included.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Reproduction burner tubes that fit the 117, 117A, 118, 118A, 118B, 119, 132P Lamps. Also in the 220 and 228 Slant lanterns.

These measure 2-1/2 inches long.

Used generator nut for the Q77 generator. 

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

Used Pump Assembly Spring

Spring ONLY

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.

Used steel generator nut. Steel nuts were used on wartime 242B, 220BX, and 220C lanterns. These will show some rust.

Original used green logo lamp globe made between 1935 and 1945. Logo is very lightly stamped as was common back in the old days. This globe measures 6 inches tall. The top rim opening has a 3 5/8 inch diameter. The bottom opening has a 3 1/2 inch diameter. It bulges out at the widest point to about 5 inches. 

NOS gas tip - Will come in either one of the packages that are pictured

New Old Stock check valve. Little tarnished, but show no signs of wrench marks. Check ball moves freely. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

Reproduction long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

NOS tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.

NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

NOS generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.