L427

Peerless 2C-HG mantles, 4 per pack (M01). These are the most popular size mantles for many Coleman lanterns and lamps. Same size as Coleman 21A mantles and fit models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Made in India. Burn off outdoors first due to smoke.

Installation instructions are HERE if needed.

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal the typical Coleman lantern cap.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point. The inside diameter of the 427 pump tube measures .68 inches or 11/16".

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345 or 2217976

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

New Coleman-manufactured 2-pack of ball nuts. This is the common size used on the majority of Coleman lanterns.

Also known as part number 3000005384.

This globe is used. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. 

Also known as part number 2000026613.

New R55 generator designed for early Coleman models. This is a common upgrade for older lanterns and lamps. Lanterns: Air-O-Lantern, 327, 427, and 220/228 Slant. Lamps: CQ series, 117, 130G-K-P, 131P.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is a quality made reproduction Q99 generator made here in the USA that fits the older Coleman QuickLite style lanterns and lamps. 

Will fit these models: 117, 117A, 118A, 119A, C331, CQ, Model B and Model C Lamps. Poultry, 227, 327 and 427.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.

Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

NOS brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

Used Gas tip that Fits 220/228 model lanterns. Will also work on many lamps that use the same generator 220E5891.

Vent rod for the Quick-Lite lanterns. It is 1 1/4 inches long.

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in nice shape.

Reproduction filler cap insert for the older winged style filler caps used on model 427 lanterns. Comes with the new gasket.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

These are NOS Coleman ball nuts

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Steel body Q77 generator. Probably made during WWII or possibly even WW1. New old stock but very tarnished from age.

This is the small check ball for the 427 lantern with an external pump. In the photo below, you can see the application. These are made from 440C Stainless Steel, the original was brass.

These are reproduction brass ball nuts. This is the common sized ball nut used on most Coleman lanterns.

Reproduction plastic parts safe that fits all Coleman model 220, 228, 236, 237, 252 Milspec, 290, 295, and QuickLites. These are made in Colorado for us by a lantern and stove enthusiast. The bottom can pop out and the ring can be used as a protector only if desired. Plastic is flexible and won't scratch the paint of your fount.  

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically, this is used on the old 327 QuickLites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage. May have small smudges.

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

NOS Old Style R55 generator with the square nut.

Packaging may vary from what is pictured.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. 

Made of 100% Teflon - the original was graphite. These seal well and can be reused.

This is a reproduction air stem for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.

Reproduction long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Full box of Peerless 2C-HG mantles – 25 packs of 4 mantles each (100 mantles total). These are the most popular size for many Coleman lanterns and lamps, the same size as Coleman 21A mantles. Fits models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Great bulk option for serious users or shops. Made in India. Burn off outdoors first due to smoke.

Installation instructions are HERE if needed.

This is a used collar for the model 327, 427, and similar lanterns. 

Some will have some surface rust - all will vary with wear.

New old stock valve for the late model L427 lantern. Also fits model 227.

New black carry case for models 220s, 290s, 295, 327, & 427, Quick-Lite lanterns and other larger sized lanterns.

Will not work for smaller lanterns like 200A, 286, 288 or 335.

Used brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

NOS Old Style R55 generator with the square nut.

They are not in original packaging and some of the square nuts are rusted.

NOS R55 generator with the square nut. Will fit on Lamp Models 117, 130G, 130K, 130P, 131P, 156, 158, 159, 168, 169X & other. Will fit on Lantern Models 327, 427, and Slant 220/228.

Packaging may vary from what is pictured.