143

Reproduction filler cap gasket for Coleman 3-piece fuel caps. Fits most Coleman lanterns and stoves that use the standard 3-piece cap with the center bolt. Good fit & quality replacement that helps stop fuel leaks. Red cap shown for reference only.

Look HERE for how to install these.

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.

Fits Coleman Lantern Models: 220B through 220K, 228B through 228K, 275, and 275A.Fits Coleman Lamp Models: 117A, 118A, 118B, 119A, 132A, 133, 143, and 150.Fits Sears Lantern Models: 476.74060, 476.72212, 476.72213, and 476.74070.

Used generator nut for many Coleman models. These are in fine shape, just dirty.

10-pack of reproduction filler cap gaskets for Coleman 3-piece fuel caps (S41). Ideal for many Coleman lanterns and stoves using the standard size cap with center bolt. Smart way to keep spares on hand and keep your gear leak-free. Red cap shown for reference only.

Look HERE for installation instructions.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

This is a new reproduction T-handle pump. It works great to pressurize your Coleman lantern, lamp, or Handy Gas Plant. Approximately 10 inches long.

Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. If your lantern diagram calls for part number 220E5891, this is what you need.

These are from used generators - they are straight and may or may not come with gas tip. They will most likely need to be cleaned. Does not come with needle and may have remnants of old internal packing/springs.

Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.

Will show signs of use but will be in good shape.

10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width. 

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

NOS brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

Used Gas tip that Fits 220/228 model lanterns. Will also work on many lamps that use the same generator 220E5891.

New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.

New old stock T44G generator. This is the early version of the 220E5891 generator. Instead of a cardboard tube it has a cloth material over the spring. These show a bit of tarnish from being on the shelf for 80 years.

Will fit Coleman Lanterns: 220 B thru 220 K, 228 B thru K, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070

The original box is not included - just showing as an example of the original packaging. 

One generator is included.

New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.

This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.

Reproduction small pump for the Coleman irons. Will also work on any Coleman lamp or lantern.

Reproduction needle for the 220E5891 generator. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Shade holder rod for later style lamps that took a globe and paper shade. Measures 1 1/4 inch long.

This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

143 Lamp Decal

Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.

Also has been reported that it works on "some" AGM check valves.

How to Use Your Check Valve Removal Tool

Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.

Follow these steps carefully to remove and reinstall the check valve safely:

1. Identify the check valve type. Pull out the air stem (pump rod) and match its threads to one of the tool's rods: Large or Small. (Most pre-1980s Coleman models use the Large size; newer ones often use Small.)
2. Thread the rod into the check valve. Hand-screw the matching rod into the check valve threads, finger-tight only. Aim to bottom it out or engage as many threads as possible—adding a drop of light lubricant (like oil) can help if it's stubborn. Critical: If it only turns one or two rotations and doesn't catch properly, stop! That's not enough thread engagement, and forcing it could damage the valve or tool.
3. Assemble the tool. Slide the outer tube down over the threaded rod.
4. Engage the prongs. Gently rotate the outer tube until the prongs fully seat into the check valve's grooves/slots. (Note: On early valves, the fit may feel tight; on later ones, it may feel looser due to natural Coleman manufacturing variations—this is normal.)
5. Secure the assembly. Screw the wing nut onto the exposed end of the rod to lock the tube and prongs in place. Tighten it snugly by hand—do not over-tighten, as this could strip the valve threads.
6. Remove the check valve. Use a long crescent wrench on the tool's flats. Hold the fount steady (a second person helps here) and turn the wrench quickly counterclockwise to break it loose. If it's really stuck, tap the long wrench handle sharply with your fist or a rubber mallet for a controlled shock—often more effective than steady pressure. Once loose, finish unscrewing by hand.

To reinstall the check valve: Simply reverse the steps above.

• Tighten only until snug—do not over-tighten as you can damage your new check valve’s threads.
• No thread sealant is required, though a light lubricant on the threads can make future removal easier.

If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!

For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% Teflon - the original was graphite. These seal well and can be reused.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P4 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.

Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.

Used steel generator nut. Steel nuts were used on wartime 242B, 220BX, and 220C lanterns. These will show some rust.

NOS gas tip - Will come in either one of the packages that are pictured

Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.

NOS air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.

Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.

Used brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.

This is a NOS older style brass mixing chamber for the 220-228 series lanterns.