214

Peerless 2C-HG mantles, 4 per pack (M01). These are the most popular size mantles for many Coleman lanterns and lamps. Same size as Coleman 21A mantles and fit models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Made in India. Burn off outdoors first due to smoke.

Installation instructions are HERE if needed.

Reproduction filler cap gasket for Coleman one-piece fuel caps. Fits many Coleman lanterns and stoves that use the 1-piece filler cap without a center bolt or screw. Good quality replacement that helps stop fuel leaks. If your cap looks like the one in the photo, this is the right gasket. 

Look HERE for how to install these. Green cap shown for illustration only and is not included.

Also known as part number 425A1361

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Full Box of 50 packs (2 mantles per pack).

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.

Also known as part number 425A1405.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.

Need more information on the valve core? Click HERE.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345 or 2217976

New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.

Also known as part number 242J5201.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

New 2 oz. alcohol bottle specifically for kerosene lanterns. This is the standard tool used to fill the pre-heater cup with alcohol prior to lighting the lantern.

New pre-heater cup designed specifically for the model 201 lantern. This smaller-sized cup measures 1 inch in diameter, with a center hole that accommodates a maximum diameter of 5/16".

It is also commonly used when performing kerosene conversions on model 200 and 200A lanterns.

New Coleman-manufactured 2-pack of ball nuts. This is the common size used on the majority of Coleman lanterns.

Also known as part number 3000005384.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Pump Clip

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Also known as part numbers 2000038026 & R214D046C.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits: 

• The fuel tube on the 508, 508A & 550B stoves
• On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251

New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire.Fits Coleman Lantern Models: 214 and 214A.

Also known as part number 3000005092.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

New Coleman-manufactured neoprene pump cup with a large push-on nut. This versatile part fits nearly all Coleman stoves and lanterns.

Also known as part number 6391091.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

10-pack of reproduction filler cap gaskets for Coleman one-piece fuel caps. Smart value for many Coleman lanterns and stoves using the standard 1-piece cap without a center bolt. Keeps spares on hand so your gear stays leak-free on the next trip. 

Look HERE for how to install these. Red cap shown for illustration only.

Also known as part number 425A1361

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.  

Comes with a new gasket that you will have to install.

Coleman Logo For Model 214 Kerosene Lantern

Note on Fitment:Please visually compare your original decal to the product photo before ordering to ensure an exact match for your specific unit.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

Amber globe with no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. 

This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Used cardboard tube that goes inside of the 200A and 220 size generators, and many others. 

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.

Fits models requiring part numbers 200-6381, 400-6381, 242B5381, or 621-5361.

10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width. 

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Feed Tube Assembly for the 214 Lanterns.

Also known as part number 2145231ZCL.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Used generator nut for these models: 214, 229, 286, 288, 290, 321, 335, 621, 635, 639 and 3022. 

May fit others. Also known as part number 335-2101

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Single Ball Nut. Fits all Coleman lanterns except the 242 type models. In good shape - just dirty.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.

This is a used pump square nut.

Comes with one square nut ONLY.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.