639

Reproduction filler cap gasket for Coleman one-piece fuel caps. Fits many Coleman lanterns and stoves that use the 1-piece filler cap without a center bolt or screw. Good quality replacement that helps stop fuel leaks. If your cap looks like the one in the photo, this is the right gasket. 

Look HERE for how to install these. Green cap shown for illustration only and is not included.

Also known as part number 425A1361

Replacement Check Valve and Air Stem This is the standard replacement part for most Coleman lanterns and stoves manufactured after 1946, as well as select earlier models. It features the updated design with a smaller air stem head; the included new stem is designed to replace your existing one entirely.

Fits models requiring part numbers 242B5381, 621-5361, or 2006381ZCL.

These are treated with Thorium from the factory and are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns. 

Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.

Also known as part number 425A1405.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

New 2 oz. alcohol bottle specifically for kerosene lanterns. This is the standard tool used to fill the pre-heater cup with alcohol prior to lighting the lantern.

New pre-heater cup designed specifically for the model 201 lantern. This smaller-sized cup measures 1 inch in diameter, with a center hole that accommodates a maximum diameter of 5/16".

It is also commonly used when performing kerosene conversions on model 200 and 200A lanterns.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This is a high-output generator specifically for the large kerosene models.

Fits Coleman Lantern Models: 639, 639A, 639B, and 639C.

Also known as part number: 3000005095.

This new Coleman globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C. Top and bottom opening measures 4-7/8" OD and is 5-1/4" tall.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

New Coleman-manufactured neoprene pump cup with a large push-on nut. This versatile part fits nearly all Coleman stoves and lanterns.

Also known as part number 6391091.

10-pack of reproduction filler cap gaskets for Coleman one-piece fuel caps. Smart value for many Coleman lanterns and stoves using the standard 1-piece cap without a center bolt. Keeps spares on hand so your gear stays leak-free on the next trip. 

Look HERE for how to install these. Red cap shown for illustration only.

Also known as part number 425A1361

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.  

Comes with a new gasket that you will have to install.

Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

Used generator nut for these models: 214, 229, 286, 288, 290, 321, 335, 621, 635, 639 and 3022. 

May fit others. Also known as part number 335-2101

Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Valve assembly for 635B and 639 lanterns.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

This is a used 3-piece filler cap. These caps show varying levels of wear, with chipped or missing paint. The one you receive may look like any of the examples shown in the photos. We select the best-condition pieces available first.

We are showing three different caps for demonstration purposes only to illustrate possible condition. This listing is for one cap.

It comes with or without the side vent hole (whichever is in stock when we pick your order). A new gasket is included for you to install if needed.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

New, reproduction burner cap for 321, 331, 335, 339, 621, 625, 635 and 639 lanterns. Solid brass with stainless steel screen. 

Also known as part number 335-315

Fuel Cap with pressure gauge.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.

Also has been reported that it works on "some" AGM check valves.

How to Use Your Check Valve Removal Tool

Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.

Follow these steps carefully to remove and reinstall the check valve safely:

1. Identify the check valve type. Pull out the air stem (pump rod) and match its threads to one of the tool's rods: Large or Small. (Most pre-1980s Coleman models use the Large size; newer ones often use Small.)
2. Thread the rod into the check valve. Hand-screw the matching rod into the check valve threads, finger-tight only. Aim to bottom it out or engage as many threads as possible—adding a drop of light lubricant (like oil) can help if it's stubborn. Critical: If it only turns one or two rotations and doesn't catch properly, stop! That's not enough thread engagement, and forcing it could damage the valve or tool.
3. Assemble the tool. Slide the outer tube down over the threaded rod.
4. Engage the prongs. Gently rotate the outer tube until the prongs fully seat into the check valve's grooves/slots. (Note: On early valves, the fit may feel tight; on later ones, it may feel looser due to natural Coleman manufacturing variations—this is normal.)
5. Secure the assembly. Screw the wing nut onto the exposed end of the rod to lock the tube and prongs in place. Tighten it snugly by hand—do not over-tighten, as this could strip the valve threads.
6. Remove the check valve. Use a long crescent wrench on the tool's flats. Hold the fount steady (a second person helps here) and turn the wrench quickly counterclockwise to break it loose. If it's really stuck, tap the long wrench handle sharply with your fist or a rubber mallet for a controlled shock—often more effective than steady pressure. Once loose, finish unscrewing by hand.

To reinstall the check valve: Simply reverse the steps above.

• Tighten only until snug—do not over-tighten as you can damage your new check valve’s threads.
• No thread sealant is required, though a light lubricant on the threads can make future removal easier.

If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!

For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com

This is for one used 3 piece filler cap. They are in various stages of wear. Finish may be chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

One mantle per pack. Used on 500-550 candlepower lanterns. Made in USA

Reproduction generator nut for these models: 214, 229, 286, 288, 290, 321, 335, 621, 635, 639 and 3022. May fit others. Also known as part number 288-1621.

New fount for the model 635 & 639 lanterns. 

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.

These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Generator Needle For Northstar Lantern 2000-750T 2000-750 2000-750E 2000A750. This is a reproduction part.

Compatible with 290, 290A, 290B, 621, 621A, 621B, 621C, 621D, 635 and 639 lanterns. This is a reproduction part.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. These are original caps in average used condition with varying amounts of rust (photo shows a typical example). These are solid, but ugly, good for projects where you are going to repaint things. Includes a new gasket that you will need to install yourself.

Fits most Coleman lantern models.