Reproduction filler cap gasket for Coleman 3-piece fuel caps. Fits most Coleman lanterns and stoves that use the standard 3-piece cap with the center bolt. Good fit & quality replacement that helps stop fuel leaks. Red cap shown for reference only.
Look HERE for how to install these.
Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Peerless 2C-HG mantles, 4 per pack (M01). These are the most popular size mantles for many Coleman lanterns and lamps. Same size as Coleman 21A mantles and fit models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Made in India. Burn off outdoors first due to smoke.
Installation instructions are HERE if needed.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.
Fits Coleman Lantern Models: 220B through 220K, 228B through 228K, 275, and 275A.Fits Coleman Lamp Models: 117A, 118A, 118B, 119A, 132A, 133, 143, and 150.Fits Sears Lantern Models: 476.74060, 476.72212, 476.72213, and 476.74070.
Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.
Also known as part number 425A1405.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345 or 2217976
New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.
Also known as part number 242J5201.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. Also fits the 530 Pocket Stove. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
New 2 oz. alcohol bottle specifically for kerosene lanterns. This is the standard tool used to fill the pre-heater cup with alcohol prior to lighting the lantern.
Used generator nut for many Coleman models. These are in fine shape, just dirty.
10-pack of reproduction filler cap gaskets for Coleman 3-piece fuel caps (S41). Ideal for many Coleman lanterns and stoves using the standard size cap with center bolt. Smart way to keep spares on hand and keep your gear leak-free. Red cap shown for reference only.
Look HERE for installation instructions.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Reproduction lamp globe for the later style Coleman lamps. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Also called the 355 globe.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.
Comes with a new gasket that you will have to install.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.
Fits models requiring part numbers 200-6381, 400-6381, 242B5381, or 621-5361.
Reproduction shade holder for the old CQ style lamps.
10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
NOS brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Used Gas tip that Fits 220/228 model lanterns. Will also work on many lamps that use the same generator 220E5891.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.
New old stock T44G generator. This is the early version of the 220E5891 generator. Instead of a cardboard tube it has a cloth material over the spring. These show a bit of tarnish from being on the shelf for 80 years.
Will fit Coleman Lanterns: 220 B thru 220 K, 228 B thru K, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070
The original box is not included - just showing as an example of the original packaging.
One generator is included.
New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is a used pump square nut.
Comes with one square nut ONLY.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
Used valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves, some also come with the brass in the middle. Completely interchangeable with valve wheel 425-1491.
This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket for you to install if needed.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
Older style check valve that takes the older larger end air stem. Fits the same appliances as the 200-6381 check valve does. The difference is the air stem end. Fits 249 lantern.
In the 426 stove series, this only fits 426 and the 426A. Will not fit B, C, D, E Will fit the 520 stove.
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is used check valve, the ball moves freely, but these have not been tested.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
If your part diagram calls for the 242B5381, 200-6381 or a 621-5361 check valve then this would be the correct part. Also known as part number 2006381ZCL.
This is for one used 3 piece filler cap. They are in various stages of wear. Finish may be chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
Used Pump Assembly Spring
Spring ONLY
New brass finial for lamps. Overall length is 1.5", but to shoulder it is 1 1/8".
This is the Canadian style, different than the USA style.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
