Irons

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Used generator nut for the Q77 generator. 

Reproduction small pump for the Coleman irons. Will also work on any Coleman lamp or lantern.

Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

New Old Stock Coleman Iron generator for model 4A and possibly others.

Some may be tarnished from sitting on a shelf all these years.

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically, this is used on the old 327 QuickLites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Reproduction iron filler cap. Fits most irons and other appliances that take a small filler cap.

Used original old short pump for Coleman Irons. Will work on lamps and lanterns too. Pump barrel is approximately 5 1/4 inches long. This is a used pump but it will have a new pump leather and will work just fine. This is the early style pump with the wooden sleeve and screws holding the pump to the barrel.

Only comes with one pump, other photos are to show different styles and color.

Original slot cleaning tool for Coleman irons. New old stock but will show signs of rust and tarnish.

Used original old short pump for Coleman Irons. Will work on lamps and lanterns too. Pump barrel is approximately 5 1/4 inches long. This is the later style pump with the clip holding the pump to the barrel. Will have a new leather installed.

Used original old short pump for Coleman Irons. Will work on lamps and lanterns too. Pump barrel is approximately 5 1/4 inches long. This is the later style pump with the metal cap that has two pressed dimples on the side holding the pump to the barrel.

Feed Tube Assembly for Iron Models 4, 4A, 8, 8A, 12, 609A,

Generator for Akron Iron model 2. Runs on gasoline. 

These are NOS iron filler caps that are nickel plated. They are a bit dusty from rolling around on a shelf, but should clean up nicely. Fits most irons and other appliances that take a small filler cap.

Valve and generator for the No. 5 iron.

Very little pump only for the model 615 irons with the built in pump.

Iron valve

Handle bolt for Coleman irons. Also used on the old wood handle lantern reflectors.

Gas tip.

Coleman 605 Iron generator. Gas tip marked D.

Needle for the model 615A iron.

Generator for kerosene iron.

Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.

Generator nut for the model 615 iron and the 5121 lantern.

Lock nut for the 609 iron.

Used Iron generator. Used on the model 4, 4A, 609, and 609A irons.

Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.

Used wood handle for the Coleman iron. Also is the same handle used on the lantern reflectors that had a wood handle.

NOS generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

Pre-heater cup for the model 615 kerosene iron.

Burner for the model 615 iron.

Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. The upright piece has a screen in the end of it. Fits models 4, 4A, 8, 8A and the 609A.

Used wood iron handle. Same handle as used on the Coleman reflectors with a wood handle.

This is a valve stem for a Canadian iron, but we  do not know the part number or which models it fits. The length of the entire shaft from the base of the handle to the tip is 1/5". The valve stem has been drilled out and can accept a rod.

NOS valve stem for the 220 and 228 slant lanterns. Also fits the 4, 4A, 8, 8A, 12, 609 & 609A irons that use the 604-299 (generator similar to the R55), LP 5101 Lantern and the pre- heater valve on a handy gas plant with the 501 burner. Will also work on Lamp models 117, 118, and 119 but has a different style of valve wheel.

Generator for Akron Iron model 2-K. Runs on Kerosene. 

Valve body for irons. The upright piece is 1 1/4 inches long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.

Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.

Pre-heater cup for the model 615 iron.

Valve body for the 611A iron.

Valve body for irons. The longest part is 2 inches long.

Back plate.

Valve Assembly for a model 611A iron.

Feed Tube Assembly for Iron Model 609.

Generator for Coleman Iron model 8 and 8A. Gas tip marked I. 

These have a needle, there are 2 versions of this generator, this is the version with a needle.

Used Generator for Akron Iron model 2-K. Runs on Kerosene. 

Iron valve