Reproduction filler cap gasket for Coleman 3-piece fuel caps. Fits most Coleman lanterns and stoves that use the standard 3-piece cap with the center bolt. Good fit & quality replacement that helps stop fuel leaks. Red cap shown for reference only.
Look HERE for how to install these.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.
Fits Coleman Lantern Models: 220B through 220K, 228B through 228K, 275, and 275A.Fits Coleman Lamp Models: 117A, 118A, 118B, 119A, 132A, 133, 143, and 150.Fits Sears Lantern Models: 476.74060, 476.72212, 476.72213, and 476.74070.
Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.
Also known as part number 425A1405.
Used generator nut for many Coleman models. These are in fine shape, just dirty.
10-pack of reproduction filler cap gaskets for Coleman 3-piece fuel caps (S41). Ideal for many Coleman lanterns and stoves using the standard size cap with center bolt. Smart way to keep spares on hand and keep your gear leak-free. Red cap shown for reference only.
Look HERE for installation instructions.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. If your lantern diagram calls for part number 220E5891, this is what you need.
This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.
Comes with a new gasket that you will have to install.
These are from used generators - they are straight and may or may not come with gas tip. They will most likely need to be cleaned. Does not come with needle and may have remnants of old internal packing/springs.
Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.
Will show signs of use but will be in good shape.
10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
NOS brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Used Gas tip that Fits 220/228 model lanterns. Will also work on many lamps that use the same generator 220E5891.
New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
New old stock T44G generator. This is the early version of the 220E5891 generator. Instead of a cardboard tube it has a cloth material over the spring. These show a bit of tarnish from being on the shelf for 80 years.
Will fit Coleman Lanterns: 220 B thru 220 K, 228 B thru K, 275 & 275A
Fits Coleman Lamp Models 117A, 118A, 118B, 119A, 132A, 133, 143 and 150
Fits Sears Lantern models 476.74060, 476.72212, 476.72213 and 476.74070
The original box is not included - just showing as an example of the original packaging.
One generator is included.
New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.
This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
This is a used 3-piece filler cap. These caps show varying levels of wear, with chipped or missing paint. The one you receive may look like any of the examples shown in the photos. We select the best-condition pieces available first.
We are showing three different caps for demonstration purposes only to illustrate possible condition. This listing is for one cap.
It comes with or without the side vent hole (whichever is in stock when we pick your order). A new gasket is included for you to install if needed.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
Reproduction needle for the 220E5891 generator. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
Shade holder rod for later style lamps that took a globe and paper shade. Measures 1 1/4 inch long.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% Teflon - the original was graphite. These seal well and can be reused.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P4 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
One used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. Could be any color.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.
Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.
These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Used steel generator nut. Steel nuts were used on wartime 242B, 220BX, and 220C lanterns. These will show some rust.
NOS gas tip - Will come in either one of the packages that are pictured
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.
Used steel filler cap for Coleman lanterns. These are original caps in average used condition with varying amounts of rust (photo shows a typical example). These are solid, but ugly, good for projects where you are going to repaint things. Includes a new gasket that you will need to install yourself.
Fits most Coleman lantern models.
NOS air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.
