288

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Most Popular Sized Mantles and are treated with Thorium from the factory. 4 mantles per pack. 

Use on these models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Will fit all Coleman Lamps. 

These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The green filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.

Also known as part number 425A1405.

New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. Fits Coleman Lantern Models: 200B, 286, and 288.

Also known as part number 3000005403.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.

Need more information on the valve core? Click HERE.

New Coleman-manufactured pump cup designed for all lanterns that originally utilized the rubber-style cup.

Also known as part number 639-1091.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345 or 2217976

New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.

Also known as part number 242J5201.

New Coleman-manufactured feed tube assembly. This component comes complete with a new Schrader valve and O-ring.

Fits Coleman Lantern Models: All 282, 285, 286, and 288 models.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Pump Clip

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits: 

• The fuel tube on the 508, 508A & 550B stoves
• On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

New Coleman-manufactured valve assembly. This unit includes the valve, control knob with screw, fuel pick-up tube, and a metal eccentric block.

Fits Coleman Lantern Models: 288 and 288A.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

New Coleman-manufactured neoprene pump cup with a large push-on nut. This versatile part fits nearly all Coleman stoves and lanterns.

Also known as part number 6391091.

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

These are used leather pump cups that fit most lanterns and stoves. They may need some oil and conditioning, but are still flexible. This is the typical sized 7/8" pump cups for most lanterns and stoves.

Fits models 288, 288A and 288B lanterns. If you need it for a 288, it will fit down inside your frame, but it is some work to get in there. It will not cover the lighting holes.
The frame bottom is replaced if your current lantern has riveted in springs. This one will accommodate the updated spring configuration.

This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.  

Comes with a new gasket that you will have to install.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Amber globe with no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. 

This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.

Fits models requiring part numbers 200-6381, 400-6381, 242B5381, or 621-5361.

New Coleman-manufactured filter funnel designed for lanterns and stoves.This funnel features a specific design that automatically stops the filling process once the fuel reaches the correct level, preventing overfilling.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

Used generator nut for these models: 214, 229, 286, 288, 290, 321, 335, 621, 635, 639 and 3022. 

May fit others. Also known as part number 335-2101

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Single Ball Nut. Fits all Coleman lanterns except the 242 type models. In good shape - just dirty.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.

This is a used pump square nut.

Comes with one square nut ONLY.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.