243

Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Peerless 2C-HG mantles, 4 per pack (M01). These are the most popular size mantles for many Coleman lanterns and lamps. Same size as Coleman 21A mantles and fit models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Made in India. Burn off outdoors first due to smoke.

Installation instructions are HERE if needed.

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the irons, model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

Replacement Generator New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part numbers T66, 200A2891, and 3000005089.

Fits Coleman Lantern Models: 200, 200A, 202, 242, 243, and similar Sears lantern models.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345 or 2217976

Used generator nut for many Coleman models. These are in fine shape, just dirty.

New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. Top and bottom outer diameter is 3.25" and height is 4.25"

Also known as part number R690B051.

New filler cap screw for the small cap on the 242, 243, 246, 247 & 249 lanterns and 500 stove size filler caps.

Reproduction needle assembly for the 200A2891 T66 generator used on lantern and lamp models 121, 200, 200A, 202, 242, 242B, 242C, 243, 476.72211 & 476.74550.

Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.  Also fits the model 500 stove. Will have a new gasket installed.

New reproduction generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns.

Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.

This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft. 

Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.

This is an excellent reproduction generator for Coleman model 200, 200A, 202, 234, 242, 243, 246 & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Same as the old part numbers T66, 200A5891 and 3000005089.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width. 

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.

This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.

Also known as part number 242-423

Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.

Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.

10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Check valve for the Northstar lantern. These also work as good replacements for the 242, 242A and 243 lanterns with check valves that use the pip.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Original NOS Coleman pump cup that fits most lanterns and stoves, they have been sitting around for many years and may not have their perfect shape and some are almost flat.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Used generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns. This is the older style.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is a 10 PACK of gaskets for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

Used gas tip for 200A5891 generator. Also works well for using on the 220 generators when doing a kerosene conversion.

Used generator body generator ONLY. This is the brass tube of the generator. May also have the internal spring and packing tube. Does not come with needle or gas tip.

This is a used Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.

These are on the rough side and are in various stages of wear.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install if needed.

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

New old stock nickel plated cap.
Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

New plastic tank/fount bumper that can be used on Models 241, 242, 243, 247 and 249 lanterns. These are made in Colorado for us by a lantern and stove enthusiast.  Plastic is flexible and won't scratch the paint of your fount.  

Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.

Also has been reported that it works on "some" AGM check valves.

How to Use Your Check Valve Removal Tool

Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.

Follow these steps carefully to remove and reinstall the check valve safely:

1. Identify the check valve type. Pull out the air stem (pump rod) and match its threads to one of the tool's rods: Large or Small. (Most pre-1980s Coleman models use the Large size; newer ones often use Small.)
2. Thread the rod into the check valve. Hand-screw the matching rod into the check valve threads, finger-tight only. Aim to bottom it out or engage as many threads as possible—adding a drop of light lubricant (like oil) can help if it's stubborn. Critical: If it only turns one or two rotations and doesn't catch properly, stop! That's not enough thread engagement, and forcing it could damage the valve or tool.
3. Assemble the tool. Slide the outer tube down over the threaded rod.
4. Engage the prongs. Gently rotate the outer tube until the prongs fully seat into the check valve's grooves/slots. (Note: On early valves, the fit may feel tight; on later ones, it may feel looser due to natural Coleman manufacturing variations—this is normal.)
5. Secure the assembly. Screw the wing nut onto the exposed end of the rod to lock the tube and prongs in place. Tighten it snugly by hand—do not over-tighten, as this could strip the valve threads.
6. Remove the check valve. Use a long crescent wrench on the tool's flats. Hold the fount steady (a second person helps here) and turn the wrench quickly counterclockwise to break it loose. If it's really stuck, tap the long wrench handle sharply with your fist or a rubber mallet for a controlled shock—often more effective than steady pressure. Once loose, finish unscrewing by hand.

To reinstall the check valve: Simply reverse the steps above.

• Tighten only until snug—do not over-tighten as you can damage your new check valve’s threads.
• No thread sealant is required, though a light lubricant on the threads can make future removal easier.

If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!

For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

Valve stem packing has not been changed, if one is needed, they are HERE 

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% Teflon - the original was graphite. These seal well and can be reused.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P4 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.

Used steel generator nut. Steel nuts were used on wartime 242B, 220BX, and 220C lanterns. These will show some rust.

Full box of Peerless 2C-HG mantles – 25 packs of 4 mantles each (100 mantles total). These are the most popular size for many Coleman lanterns and lamps, the same size as Coleman 21A mantles. Fits models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Great bulk option for serious users or shops. Made in India. Burn off outdoors first due to smoke.

Installation instructions are HERE if needed.

Brass Vent Bolt for 243, and 243A Lantern - this screws down into the top of the frame for the 243 vent to sit on.

NOS generator for Lantern Models 200A and 242. Includes gas tip, spring, and tip cleaning wire with a cardboard tube packing. 

These are pinned so the needle, spring and packing stay inside the generator.

This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove. 

These are in good condition.

Comes with a new gasket for you to install if needed.

This is a used small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.