This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The green filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
String Tie Mantles for Models 222, 226, 229, and 3022 lanterns. May be in different packing than what is pictured.
Also known as part number 3000004346.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Also known as part number 639-1091
They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
New Coleman Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Also known as part number 5010000290.
Original NOS Coleman Graphite Packing.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is the short pump used on the small stoves and lanterns. Smaller stoves and lanterns with the plastic top are what this is for. Some small series stoves (Peak) and lantern model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
These mica panels are 3" x 5" in size.
General information:
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket for you to install if needed.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Used Pump Assembly Spring
Spring ONLY
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Filler cap lanyard for the small backpacking lanterns.
New plastic tank/fount bumper that can be used on Models 222, 222A, 222B, 226, 226A and 229 lanterns. These are made in Colorado for us by a lantern and stove enthusiast. Plastic is flexible and won't scratch the paint of your fount.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.
These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Reproduction Generator for Model 226A700 and the 226-700. Generator includes new gas tip, spring, and tip cleaning wire.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend the 226 generator as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used - fits model 400 stove, 226 lantern. Has the smaller threads used on the newer style check valves. 3-3/4" long.
Used filler cap with lanyard for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Lanyard on this one is a little rough but still intact.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap off the Model 286 most likely.
Comes with a new gasket that you will have to install.
NOS filler cap with lanyard for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap.
Used burner frame for the 222, 229, 226A, 222B, 226 lanterns
Used gas tip for Models 226, 222 and 3022 model lanterns.
NOS gas tip for Model A Lamps and possibly other early Torch-Lite Lamps.
Used filler cap for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Does not come with lanyard.
Comes with a new gasket that you will have to install.
Used filler cap for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Does not come with lanyard.
Comes with a new gasket that you will have to install.
Used filler cap for the small backpacking lanterns. Will also fit most other lantern and stoves that use the standard size filler cap. Does not come with lanyard.
Comes with a new gasket that you will have to install.
