220 Slant

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal the typical Coleman lantern cap.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

New Coleman-manufactured 2-pack of ball nuts. This is the common size used on the majority of Coleman lanterns.

Also known as part number 3000005384.

New R55 generator designed for early Coleman models. This is a common upgrade for older lanterns and lamps. Lanterns: Air-O-Lantern, 327, 427, and 220/228 Slant. Lamps: CQ series, 117, 130G-K-P, 131P.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

New steel fuel pick-up tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".

Also known as part number 200-1481

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.

Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.

Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging.

This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

NOS, USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.

New fount/tank bumper that fits all 220, 228, 236, 237, 252 Milspec, 290, 295, and QuickLites. These are made in Colorado for us by a lantern and stove enthusiast. Plastic is flexible and won't scratch the paint of your fount.  

Single Ball Nut. Fits all Coleman lanterns except the 242 type models. In good shape - just dirty.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Reproduction burner tubes that fit the 117, 117A, 118, 118A, 118B, 119, 132P Lamps. Also in the 220 and 228 Slant lanterns.

These measure 2-1/2 inches long.

Steel body Q77 generator. Probably made during WWII or possibly even WW1. New old stock but very tarnished from age.

Used generator nut for the Q77 generator. 

These are NOS Coleman ball nuts

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.

These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 220BX, 220B, 220C, 220 & 228 Slants. Size is 4-40 x 5/16".

Reproduction plastic parts safe that fits all Coleman model 220, 228, 236, 237, 252 Milspec, 290, 295, and QuickLites. These are made in Colorado for us by a lantern and stove enthusiast. The bottom can pop out and the ring can be used as a protector only if desired. Plastic is flexible and won't scratch the paint of your fount.  

These are reproduction brass ball nuts. This is the common sized ball nut used on most Coleman lanterns.

Used Pump Assembly Spring

Spring ONLY

For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.

These made in the USA Mica Globes measure 4 7/8" x 5 1/4" and fit 206, 220, 228, 231, 236, 237, 290, 295, and QuickLite lanterns.

This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects. 

The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"

This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.

OCP Collector's Edition, Model 220F Coffee Mug - 11oz.

Vintage 200A Reproduction splined ball nut. Will fit all Coleman lanterns except the 242 type models.

NOS Old Style R55 generator with the square nut.

Packaging may vary from what is pictured.

New Old Stock check valve. Little tarnished, but show no signs of wrench marks. Check ball moves freely. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

Reproduction long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging and they are rusty on the outside. They are made of steel.

NOS tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.

Large size Coleman Sunrise globe wrap which will show off your lantern and protect the glass during travel. These are easy to attach with Velcro. 

Will fit on any lantern that uses the 220/290A/295 style globe as long as the bail handle terminates on the vent of the lantern. Make sure your bail handle hinges at the vent - otherwise it will be in the way  - see the last photo for clarification about the bail location issue.

Will fit well on the 290A, 290B and 295. Fits tightly on the 236, 237, 238, 635 and 639. Look at the photos to get an idea of how they fit - only first photo has this products design.  Will conflict with the bail on all 220 and 228 models.

These will melt, so your lantern has to be cool. Made of neoprene fabric and Velcro here in the USA.

NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Used collar for the first model 220/228 lantern. Commonly known as the slant 220 or 228. Will not work on later models.

NOS Old Style R55 generator with the square nut.

They are not in original packaging and some of the square nuts are rusted.

N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.