226

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The green filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is the small tube that goes inside of the 200A, 220/228 and 288 size generators. May fit others too.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

String Tie Mantles for Models 222, 226, 229, and 3022 lanterns. May be in different packing than what is pictured.

Also known as part number 3000004346.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

Also known as part number 242J5201.

This is a new Coleman made replacement pump cup  for all lanterns that came with the rubber style.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

New Coleman Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.

Also known as part number 3000005088.

This also fits 222 models, but please read on. 

Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using  this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605. 

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits: 

• The fuel tube on the 550B stove
• On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Fits model 400 stove, 226 and 222 lanterns.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.

This is a 10 PACK of the small tube that goes inside of the 200A, 220/228 and 288 size generators. May fit others too.

Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter. 

Also known as part number 5010000290.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8

This has been reported to be the correct size to repair the valve on the 400B and the 533A stoves. One is needed for both.

Will also work on 533B - one of these is needed along with the Viton #8 HERE

Used cardboard tube that goes inside of the 200A and 220 size generators, and many others. 

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This is the short pump used on the small stoves and lanterns. Smaller stoves and lanterns with the plastic top are what this is for. Some small series stoves (Peak) and lantern model s222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a used steel 3 piece cap.  Comes with a new gasket that you will have to install.

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket for you to install if needed.

This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #5

This is for one used 3 piece filler cap. They are in various stages of wear. Finish may be chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Original NOS Coleman Graphite Packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Used Pump Assembly Spring

Spring ONLY

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

Mica globe for the small backpacking lanterns. Will fit models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.

Would be good for camping as it will not break like glass.

This is a used 3-piece filler cap made of brass. Copper in color. This one is in good condition.

Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

Reproduction Generator for Model 226A700 and the 226-700. Generator includes new gas tip, spring, and tip cleaning wire.

This also fits 222 models, but please read on. 

Coleman discontinued the 222 generator, and they recommend the 226 generator as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605. 

Filler cap lanyard for the small backpacking lanterns. 

This is an original frosted, striped globe which originally came on some models of the 226. Fits models 222, 226 and 5133. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.