Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Reproduction filler cap gasket for Coleman one-piece fuel caps. Fits many Coleman lanterns and stoves that use the 1-piece filler cap without a center bolt or screw. Good quality replacement that helps stop fuel leaks. If your cap looks like the one in the photo, this is the right gasket.
Look HERE for how to install these. Green cap shown for illustration only and is not included.
Also known as part number 425A1361
Full Box of 50 packs (2 mantles per pack).
These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
These are treated with Thorium from the factory and are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.
Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.
Also known as part number 425A1405.
Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.
Also known as part number 3000005094.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
#11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
10-pack of reproduction filler cap gaskets for Coleman one-piece fuel caps. Smart value for many Coleman lanterns and stoves using the standard 1-piece cap without a center bolt. Keeps spares on hand so your gear stays leak-free on the next trip.
Look HERE for how to install these. Red cap shown for illustration only.
Also known as part number 425A1361
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone. We have been told that these will fit the 533 Stove - 2 are needed.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.
Comes with a new gasket that you will have to install.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Stainless Steel burner frame to valve nut for the 200, 200A, 201, 202, 222, 222A, 222b, 237A, 237B, all the 242s, 321B, 325A, 331, 335, 339, 621A, 621B and 635 lanterns. May also fit other models and some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Also listed in diagrams as part number 604A456.
These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
This is a high-quality reproduction of the older style check valve designed to accommodate an original air stem with the larger ends. This part does not include an air stem, as it is intended for use with your existing old-style stem.
Fits models requiring part numbers 200-6381, 400-6381, 242B5381, or 621-5361.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
USA made red letter globe. This globe will fit models 275, 275A, 621, 621A, 621B, 5114, 5114A, 5114B, and 5114C. It is approximately 5 1/4 inches tall. The large opening has approximately a 5 7/8 inch diameter. The smaller opening has approximately a 4 5/8 diameter. Same size as the Canadian 880 globe.
This is a used pump square nut.
Comes with one square nut ONLY.
Compatible with 635 and the 621 series lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Coleman Canadian lantern generator G6 (635A297).
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket for you to install if needed.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
New, reproduction burner cap for 321, 331, 335, 339, 621, 625, 635 and 639 lanterns. Solid brass with stainless steel screen.
Also known as part number 335-315
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is used check valve, the ball moves freely, but these have not been tested.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
If your part diagram calls for the 242B5381, 200-6381 or a 621-5361 check valve then this would be the correct part. Also known as part number 2006381ZCL.
Used Pump Assembly Spring
Spring ONLY
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Reproduction generator nut for these models: 214, 229, 286, 288, 290, 321, 335, 621, 635, 639 and 3022. May fit others. Also known as part number 288-1621.
One used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. Could be any color.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.
These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Fits models 621 and 635 lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.
How to Use Your Check Valve Removal Tool
Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.
Follow these steps carefully to remove and reinstall the check valve safely:
To reinstall the check valve: Simply reverse the steps above.
If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!
For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
