Reproduction filler cap gasket for Coleman 3-piece fuel caps. Fits most Coleman lanterns and stoves that use the standard 3-piece cap with the center bolt. Good fit & quality replacement that helps stop fuel leaks. Red cap shown for reference only.
Look HERE for how to install these.
Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Peerless 2C-HG mantles, 4 per pack (M01). These are the most popular size mantles for many Coleman lanterns and lamps. Same size as Coleman 21A mantles and fit models including 200, 200A, 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5100 series, 5150 series, 9950, 9960 and most other Coleman pressure lanterns. Treated with thorium at the factory for bright white light. Known for being more durable and rugged than standard mantles. Made in India. Burn off outdoors first due to smoke.
Installation instructions are HERE if needed.
Reproduction generator tube packing for Coleman lanterns. This is the small tube that fits inside the generator on models 200A, 202, 220, 228, 242, 275, 288 and may fit others. Good quality replacement that helps keep your lantern running cleanly and reliably.
Reproduction large valve stem packing for Coleman lanterns and stoves (242-6201). Fits many older Coleman models that use the larger size packing on the valve stem. Good quality replacement that helps stop fuel leaks around the valve. Made of 100% graphite from here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
New Coleman-manufactured generator including a new gas tip, spring, and tip cleaning wire. This part is equivalent to old part number T44 and new part number 3000005090.
Fits Coleman Lantern Models: 220B through 220K, 228B through 228K, 275, and 275A.Fits Coleman Lamp Models: 117A, 118A, 118B, 119A, 132A, 133, 143, and 150.Fits Sears Lantern Models: 476.74060, 476.72212, 476.72213, and 476.74070.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.
Also known as part number 3000005094.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Burner screen for double mantle lanterns and lamps. Fits 220s, 228s, 117, 129, 129G and CQ lamps. Fits most double mantle lanterns and lamps with small burner caps.
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 252, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345 or 2217976
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
New Coleman-manufactured 2-pack of ball nuts. This is the common size used on the majority of Coleman lanterns.
Also known as part number 3000005384.
Used generator nut for many Coleman models. These are in fine shape, just dirty.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
This also works well as part number 335-0604 used on the burner frame/tube for the 335 lantern.
10-pack of reproduction filler cap gaskets for Coleman 3-piece fuel caps (S41). Ideal for many Coleman lanterns and stoves using the standard size cap with center bolt. Smart way to keep spares on hand and keep your gear leak-free. Red cap shown for reference only.
Look HERE for installation instructions.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
New steel fuel pick-up tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Also known as part number 200-1481
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.
This is a used valve assembly for the models 220/228B through 220/228F and 252/Milspec lanterns. Valve packing has not been changed. If needed, they are HERE.
220C6531 is the part number for the valve stem inside this valve.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
In the 426 stove series, this only fits 426 or 426A
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire. If your lantern diagram calls for part number 220E5891, this is what you need.
NOS fuel and air tube for model 220 & 228 through B through K lanterns.
Direction disk for the military lanterns. These came out of the old SMP factory.
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Reproduction check valve for the military lanterns. Will also fit the models 220/228B and 220/228C. Will not fit the later style lanterns.
10-pack of reproduction generator tube packings for Coleman lanterns. This is the small tube that fits inside the generator on models 200A, 202, 220, 228, 242, 275, 288 and may fit others. Good quality replacement that helps keep your lantern running cleanly and reliably.
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
New reproduction generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns.
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
These are from used generators - they are straight and may or may not come with gas tip. They will most likely need to be cleaned. Does not come with needle and may have remnants of old internal packing/springs.
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
Used cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.
Will show signs of use but will be in good shape.
10-pack of reproduction large valve stem packing for Coleman lanterns and stoves. Same as 242-6201. Fits many older Coleman models that use the larger size packing on the valve stem. Smart way to keep spares on hand and stop fuel leaks around the valve. Good quality replacement that helps keep your gear working right. Made of 100% graphite here in the USA.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Zippo brand Flints for the Coleman Lantern Spark Igniter.
NOS brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
New Coleman-manufactured filter funnel designed for lanterns and stoves.This funnel features a specific design that automatically stops the filling process once the fuel reaches the correct level, preventing overfilling.
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
Vent rod for the Quick-Lite lanterns. It is 1 1/4 inches long.
10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
